Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
microwave would not heat
First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!
Symptom: Terrible sparking coming from the right side of the microwave even with nothing in the microwave. The part that was behind the cover was the business end of what I learned was the magnetron,
Repair process: Without appliance repair experience I went onto Google and searched for parts for my model PEB1590DM2WW. I was able to find a great parts schematic on partselect.com. At first I ordered a magnetron and while waiting for the parts to arrive I also learned that the capacitor can also fail easily as described in the other install feedback on the partsselect website. So I ordered a capacitor just in case. These convection microwaves are around $600 new so a $80 in parts is not out of line for 8 years of service. I installed the magnetron first and turned it on. sparking immediately continued so I quickly shut the unit off. After replacing the capacitor and letting it charge for several minutes before trying to start the microwave cycle was the issue. I choose to leave the replaced magnetron as the original unit was discolored and felt the replacement was inexpensive insurance. I also learned that if the wave guide (which is a plastic/metallic composite material) that covers the opening to the magnetron is burnt or has metal melted to it as mine did it will act similar to the microwave having metal inside the enclosure and will continue to spark and basically melt the wave guide further. Replacing the wave guide was very easy as well.
I am very thankful for the knowledge base and support available from Partselect.com as they made this repair possible on my own. Thank you partselect.com
Pretty simple but required buying a set of security bits (#68549) from Harbor Freight for $7.00 to remove the outer cover of my GE JES2051SNSS microwave. At first glance I thought the cover would remove by going towards the front of the microwave, but it ended up just needing a tug to the rear. I like this site because they have pictures of the exploded appliances that show what your getting into.
Microwave does not have power at all, though outlet has power
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
Removed cover discharged the capacitor and looked around for obvious signs of component failure. Then began testing switches and sensors finding flame sensor closed. Did a bypass and all cylinders fired. Part needed no longer available. Located your part with almost exact working values and installed it. Hopefully will get another 12+ years of service. I have used you folks in the past and will in the future. Thanks
Opened door to get food put more food in closed door it wouldnt work
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a new one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill. My micro is only 2 years old so I was hoping it wasn't anything major.
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
To remove the outer cover of the microwave you have to unscrew 7 or 8 Phillips screws but most of them have "secure" type heads, so you need a driver with a hole in the middle, to fit over the pin on the screw head. I had one of those already, so it wasn't a problem. The metal cover is slid between rubberized strips on the front face of the enclosure and needs to be lifted and tugged out quite firmly in order to release it. Once the cover was removed, the bulb can be seen attached to the main frame of the microwave by a soft metal lug that can be bent back by hand to release the bulb and its integrated holder. The wiring harness simply pulls off of the bulb prongs and there you have the charred remains of the original bulb! I tried every appliance store and hardware store in Bismarck, but nobody had this part. When I typed in the serial number on the bulb, Partselect's site came up with exactly what I needed. Replacement was a simple reversal of the process, making sure not to over-tighten the sheet metal screws on the cabinet. Voila! We have light beams again. Thanks Partselect.
I removed the main cover ( torx security bit required) and tested the magnetron, capacitor, diode and door interlock switches according to instructions found on the internet. The capacitor and diode tested good but the magnetron looked burnt and corroded on the tip. The magnetron I received was an exact replacement for the original. It was easy to replace the magnetron which arrived in 2 days standard shipping. I also cleaned the fan while I had access to the inside area. Hoping to get another 18 years use from the microwave!
unplug oven from power remove glass turntable remove cabinet housing remove burnt out bulb order correct part reinstall new bulb reattach cabinet housing install glass turntable plug into power outlet confirm light bulb on
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin. Turn the ice maker selection to "OFF" Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one. Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug) Move the selector from "OFF" to "ON" Replace the ice bin and close the freezer door
Unplugged microwave from wall outlet removed the cover with standard phillips #2 screwdriver and tamper proof screw bit driver. For safety shorted across capacitor with insulated needle nose pliers to discharge. With P2 screwdriver removed 2 latch board screws and rotated latch board to access switches. Even though only the bottom primary interlock switch was mechanically broken, I replaced the upper primary interlock switch also. With a DVM I checked the middle switch which tested good. The old switches can be carefully removed from the latch board by slightly bending the lock tabs and unplugging them, installation is the reverse of removal. I tested the release button and latch mechanism before replacing the cover. I tested the microwave only with the cover on for safety. Parts arrived quickly and easy repair on an 18 year old reliable microwave. A year ago, I replaced the magnetron, capacitor and diode on the same unit which did not heat.
I assumed light was burned out and got a replacement bulb. Removed back and side screws with slight difficulity. Was not able to remove cover. The top front would not loosen. I tried every trick in my 80 year repertoire. I gave up and put it back together. I emailed PartSelect last week explaining the problem. So far no reply. I am sure I have the right model # and others seem to have little trouble removing the cover. I paid $85 + tax for the oven and it has worked well for about 8(?) years. From what I read here, I figured I could handle the bulb replacement. I'm just out the cost of the bulb and shipping and the oven still works. It would have been nice to have the light work again but we will just wait until it quits working and buy another inexpensive unit.
