Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave was accidentally overheated and all power was lost.
Since I didn't know if it was the current fuse or the flame sensor, I ordered both parts, and, I had to order the tamper proof torx bits needed to remove the microwave cover ($7.45 on Amazon). Once the cover was off the unit, both parts were easily accessible on top of the oven and were replaced in only a couple of minutes.
e.g. First I removed the bottom cover. I then removed the two screws that hold the motor in place. I then pulled the motor out about 3 inches and disconnected the two wires...) I then put the new motor in with the two screws and hooked the wires back up. I then replaced the bottom cover and put the the turn rack and glass tray back in place. Works great.
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Hubby put in two cold hard boiled eggs in shell to heat and microwave plate bursted.
After picking up the broken glass and cleaning up the mess, I looked up GE microwave turntable plate and came across this site! Easy to order on their website, good price, and quick delivery.
The turntable move intermitently and made a lot of noise.
Once I unpluged the unit and laid it on its back, I remove four screw and exposed the motor. The motor was mounted with two screws and a push on electrical conecter. I reversed the procedure and it was done.
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
Remove the ice bin. Turn the ice maker selection to "OFF" Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one. Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug) Move the selector from "OFF" to "ON" Replace the ice bin and close the freezer door
-unplug -remove top and front covers -unplug wire connectors from heating assembly -remove heating assembly from metal stand and push out of the way -remove metal stand from dry -pull out heating assembly -install new one in reserve order
stem on bottom of guide cracked and became too loose to drive turntable
It took quite a bit longer to decide which one of the roller guides in the selection was the right one, than to install the new one. Got it right though, works great
I replaced the door key, it was broken on the side so it was not touching the sensor for shutdown. Replaced the door key and the backframe keep the microwave like brand new
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.