JDB2100AWS Jenn-Air Dishwasher - Instructions

After checking the door switch I found the micro switches were working but the unit would not start on the control panel. Thinking the latch was worn, I ordered a replacement. After changing the replacement latch and switches that came with it, the unit would still not start. I checked the switch and it is making contact. I can start the unit after I close the door using the handle of a pair of pliers. So I assume the control board is bad, due to the fact that it will not initialize the control panel until the door is closed. Now I have ordered a control board and will replace...stay tuned!!

found the part here.. it was shipped FAST and worked perfectly as it is just like the original part. thanks

1. Turned off power. 2. Unscrewed ten screws holding inside of door in place. 3. Lifted cover enough to access latch - helpful to have someone to hold this while doing the job. 4. Disconnected old latch assembly on each side - this was the hardest part as they were stiff and needed to be pulled hard. 5. Attached new latch assembly. 6. Screwed door panel back on. 7. Switched power back on. So easy and saved about $150. This stuff is NOT HARD and I just wish more people had the gumption to do repairs themselves instead of paying 'experts' to do exactly the same job.

Removed all the screws holding the shroud, filter, wash arm, etc. Installed new shaft and chopper blade, then reinstalled impella on new shaft as described on the easy to follow instructions.

the small plastic part that turns the dishwasher off and on when the door is shut was worn out. It was really easy to change out. I unplugged the power cord and removed the black and white wires. Put in the new switch and it was ready.

Added toe panel and insulating strip.

You guys were FANTASTIC in getting the one plastic clip to me. Jenn air had discontinued the part and I was unable to order it from them. But you guys had it in stock and saved the day.

Before starting the job, I looked at the information provided from others who had the same problem and had successfully installed the new part. The information provided was the reason I chose your company to purchase the part. THANK YOU!
1. Turned off power
2. Removed screws holding inside of door.
3. Disconnected and removed old part.
4. Removed dishwasher door handle and attached to new part.
5. Connected new part and positioned it in the handle insert. (Be sure the small bars holding it together are firmly in place.)
6. Reattached the door.
Here is the problem: I did not realize I also needed a new door handle as I assumed it would be attached to the new door latch assembly. My door handle is cracked and some of the plastic has broken away. I will now have to order the new handle and pay the cost of shipping that would have certainly been less if I had ordered it in the first place.

After truning off the power, I removed the inside door panel by unscrewing the 11 screws. Next unplugged the latch assembly from the two electrical connections. Connected the two electrical connection to the new part and reinstalled the inside door panel. The only difficulty was that the first part I ordered did not have a handle as part of the assembly.

i deinstalled everything in the ground of washer so that i saw the e motor
take of the part from the motor and install your new part
and reinstalled everything

Remove all screws on inside panel disconnect wires remove switch

simply remove the basket from the dishwasher. Remove the screws from the adjuster and replace with new part.

the person at part select i spoke to by phone was helpful. the shipping was very fast. i did not need the sound seal, however, as one was already attached to the toe panel. i could not tell this from the pictures online, nor did the customer service rep know this. also, i did not need the screws as the part just snapped in. my dishwasher is stainless steel and the toe panel is black but still looks good.

I replaced a tempermental Maytag with a new Electrolux dishwasher. The new dishwasher didn't include any decent trim strips so I ordered the two maytag strips like my old unit had. Looks great. Easy to install. FAST shipping!

Very nice people to deal with. Normally this kind of experience you never expect from a service company.
Thank you.