Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JCTP70SM1SS > Instructions

JCTP70SM1SS General Electric Wall Oven - Instructions

All installation instructions for JCTP70SM1SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JCTP70SM1SS
1-15 of 26
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven was not coming up to temperature

  • Customer: Sean from Highlands Ranch, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 36 of 41 people found this instruction helpful
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.

Oven Lamp Holder Burned

  • Customer: Jack from Okmulgee, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 15 people found this instruction helpful
removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

Actual temperature did not match set temp

  • Customer: Brian from Fairfield, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and screwed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.

F2 error code

  • Customer: George from Fiskdale, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 14 people found this instruction helpful
After reviewing the potential causes for the error code, I decided I'd try to change out the temp sensor. Using the ohmeter, I saw the difference immediately between the old and new sensor. The sensor is accessed from the back of the stove, and must be slide out to gain access to the rear panel. Since the stove I have is a built in, removing the stove and the access panel was the hardest part of this repair. Resetting the glass control panel was also a bit tricky to calibrate the touch sensitive buttons. Good luck.

wire connection to socket was bad

  • Customer: David from Gansevoort, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

Oven slow to heat.

  • Customer: Scott from Burleson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.

Oven light did not work

  • Customer: Howard from Rio Vista, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

f2 and f3 codes oven would shut off

  • Customer: garry from manhattan, IL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
lift door off and remove racks take out old sensor. one word of advise when pulling old sensor out tie a string around connector coming out of oven if it slips out of yor hand it could fall through hole iif you dont have a string attached you pull the whole oven out of wall to acess it

Oven Light Assembly damaged

  • Customer: Jose from Frederick, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 3 of 5 people found this instruction helpful
I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

oven not as hot as temp display said it was

  • Customer: John from HOT SPRINGS, AR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

Oven tempeture off by 50 degrees

  • Customer: James from CHESTER SPRGS, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

Door latch would not allow you to remove food when done cooking

  • Customer: STEVAN from LEAVENWORTH, WA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Turned breaker off at panel first. Removed three sheet metal screws holding top control panel with 8mm socket, removed the two 8mm nuts holding the locking mechanism in and one 8 pin plug, replaced with new part. Put back control panel and I was enjoying homemade oatmeal cookies 30 minutes later. We were using a toaster oven for months until I found the part from this site. The GE repair guy wanted $900.00 to fix it. The part was only $165.00 from this site. Thanks folks!

the temp was not accurate

  • Customer: scott from new harmony, UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 3 of 8 people found this instruction helpful
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.

gasket on door was brittle

  • Customer: Barbara from Bethesda, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I feel like Macho Mom. I called in the repair guy since I was afraid of dealing with the gas. HE repaired one item but could tell I was comfortable fixing things and pointed out that the gasket was brittle and would cause major problems if not replaced. Took longer to order the part than do the repair, don't know what I was afraid of!

Oven temperature was low when reading was correct

  • Customer: Orion from Vancouver, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!
All Instructions for the JCTP70SM1SS
1-15 of 26