Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.
After calling a appliance repair person out because I could not find the module, he pulled the range out so he could remove the top, back cover. He used the correct nut-driver to remove the back. The module is attached to the cover and is exposed when you take it off. Just gently pry the module from the cover. When I saw where it was I paid the repair person for his visit and ordered the new module from PartSelect.com. When it arrived I proceeded to install the new module. I had to use pliers to grasp each connector going into the module and use a flat bladed screwdriver between the module and pliers to get each one to release. I took one wire off at a time and inserted each one into the new module, corresponding to the place it came out of the old module. When I had all the wires inserted into the new module I pushed the new module, using a flat bladed screwdriver, back onto the back cover of the stove. Reattached the back cover with the metal screws and pushed the range back into place. All burners are lighting as designed.
I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.
Actual temperature in oven was not consistent with the temperature setting
I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.