JB960AY1 General Electric Range - Instructions

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

TURN OFF POWER , remove oven door & oven wire racks, remove two retaining screws in back of coil and pull the burnt coil foward enough to remove the screws that hold the wires to the coil. You may have to drop one side of the front support bracket to move coil forward.Fasten the new coil to the broiler wires with the new screws provided. Push the new coil back into place being careful not to pinch the wires in the opening. Refasten coil to the oven back with existing screws that you removed. Refasten front support.Put racks back in and put door back on.Easy fix! Easy to order, easy to install and came within days from order date. Very pleased with whole thing.

Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.

plug in thermistor when needed

Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussing. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!

REmoved the covers, removed the old part, be careful with the electrical connections, they move back behind the wall and are hard to get back in the open. While waiting for the new part, 2 days, I cleaned the oven. Works like new.

Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.