Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven Igniter went out the night before Thanksgiving
First I took out the old Igniter and discovered the part I ordered did not come with any connectors, just bare wires. This is ok but I found myself searching the stores for the correct attatchments. It would be great if your web site gave the options to order these at the same time. This was my first repair of this kind so I had no idea what I was doing. I thought the part would arrive with what I needed to install it. The hardest part was getting the bolts off the under side of the Igniter. The space if very tight and at an angle that a regular took doesn't really fit. What took so long was taking the bolts off by hand. Im a single woman who likes to try to fix things first on my own. My 18 yr. old daughter was in there with me the whole time learning and finally it was her smaller fingers that were able to get the bolts into the new part. We only finger tightened the part because no tools would fit at the curved angle. I love your web site and the ease of finding the part I needed. Its the stove manufacture who made this project difficult by how they place the screws. I will use them for all my part needs in the future.
I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.
The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.
After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.
Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.
Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse order. Tested oven operation to ensure that the gas ignited promptly. (It did).
Removed the two screws that hold the oven bottom to expose the glow element. Also removed the lower draw to get to the connections. The job was only complicated by getting to the two bolts holding the glow plug to the oven frame. Getting them off and getting the new plug on was not easy with standard tools. There was not a lot of room to work the hex bolts and i wound up cutting the old unit out and attaching the bolts to the frame and cutting slots in the new unit so I could slot it in. That worked. The glow plug was the problem and the oven came right on.
First shut down electric power to oven. remove oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires. installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.
First i removed the inside bottom of the oven where i could get to the actual glow plug igniter and removed the two screw that held the igniter in place. I than pulled the entire oven out allowing me to access the two wires connecting the igniter to the stove. I disconnected the wires and had to splice the wires as to be able to reach the appropriate connections. I reinstalled the igniter and upon testing the igniter worked properly. The entire process took me one hour.
Followed suggestions of previous posts. Removed oven door, warming drawer, pan in bottom of oven. Removed element to replace igniter. One thing I would add is I put a small piece of electical tape on the heads of the two 1/4 in. screws for the rear element bracket. This kept them from falling out of nutdriver.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
I really do not have the time to do this right now, however, I feel that it is important to tell everyone that dealing with PartSelect allowed me to repair the stove and please my wife in the easiest way possible. I will use PartSelect forever....
When turned on, oven wouldn't ignite and gas wouldn't flow
Diagnosed the problem as igniter failure and called local parts outlet. They gave me the part number, but said they were out and directed me to another vendor. When the part came, it was the wrong shape but I tried it anyway. Result - the igniter glowed which allowed the gas to flow, but igniter, being the WRONG PART, didn't ignite the gas, allowing a dangerous build-up of gas.
I then went to PartSelect, looked up the part, saw it was the correct one, ordered it (arrived within 3 days) and, because I already had the pans and covers off the oven, it was a matter of minutes to install. Works like a charm and, though I usually like to buy locally, I'll check out PartSelect first next time!
I removed the 2 screws that held the bottom oven plate in place. Then I removed the one screw holding the bottom burner in place in the front. I then reached into the rear area and unscrewed the last 2 screws securing the burner. I disconnected the igniter wires at their push-on connections and lifted the whole burner/igniter unit out. I relaced the igniter using the 2 attachment screws, and I cut the old igniter's wires with connectors and spliced them into the new igniter's wires, using the ceramic wire nuts that came with the new igniter. I reassembled the unit and it worked first time.
oven not working, broiler working, burners working
i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!
Oven would not work. Burners worked fine. Igniter would not glow.
It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.
• Start by unplugging the unit from the wall. • Then slide the unit out carefully without damaging the gas line. • Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools. • Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is. • Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place. • Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is. • Remove the igniter 1-2 screws • Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered**** • Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under**** • Reassemble the range and replace the drawer. • Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.
Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.