Models
>
HDE2000GA
HDE2000GA Maytag Dryer - Overview
Sections of the HDE2000GA
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Multi Rib Belt - 92-1/4"
PartSelect #: PS346995
Manufacturer #: 341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the ro...
$17.19
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Blower Wheel Clamp
PartSelect #: PS11740752
Manufacturer #: WP312967
This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clo...
$13.61
In Stock
Rear Drum Support Roller Kit
PartSelect #: PS2162268
Manufacturer #: LA-1008
The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four s...
No Longer Available
Screw
PartSelect #: PS11740978
Manufacturer #: WP3196164
This screw is sold individually.
$7.68
In Stock
Blower Wheel - B/10 Models
PartSelect #: PS2030820
Manufacturer #: 31001043
This blower wheel is suitable for some clothes dryers of the 10 and earlier series. Manufactured to fit a 1/2 inch motor shaft, this blower wheel is 3-1/8 inches deep. The diameter of the wheel is 7-1...
$75.65
In Stock
High Limit Thermostat (Limit: 258-80)
PartSelect #: PS11742806
Manufacturer #: WP53-0771
This high limit/safety thermostat is used on many gas and electric clothes dryers. It is made of metal, and is almost two inches long. With this thermostat, a dryer's heating element will cut out if t...
$82.43
In Stock
Drum Felt Seal
PartSelect #: PS11740735
Manufacturer #: WP31001747
The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your p...
$39.87
In Stock
Thermal Fuse
PartSelect #: PS11742810
Manufacturer #: WP53-1182
This part is the replacement thermal fuse for your dryer. It measures a little more than an inch wide, and about ¾ inch long. The thermal fuse is a safety device that shuts off the burner in a gas dry...
$37.78
In Stock
Retaining Ring
PartSelect #: PS2026490
Manufacturer #: 25-7855
This part works in conjunction with the blower wheel.
No Longer Available
Front Glide Kit
PartSelect #: PS2003584
Manufacturer #: 12002126
This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.
$85.16
In Stock
Drum Glide and Cushion Kit
PartSelect #: PS2162266
Manufacturer #: LA-1006
Pad has adhesive backing.
$27.64
In Stock
Questions And Answers for HDE2000GA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the HDE2000GA
[Viewing 7 of 7]Noisy
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Heat stays on after drum has stopped
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken tumbler belt
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
Read less
Parts Used:
-
Michael from San Antonio, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
130 of 149 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt - drum would not turn
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer
... Read more
ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.
Read less
Parts Used:
-
Gary from Oakland, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
81 of 95 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer squeaking really badly
I opened the dryer from the front by pushing in on the two clips just under the top. I then had to remove two screws on each side and took the front panel off. I reached around underneath on the right side to slip the belt off the pulley. I pulled the drum out and then I could see the roller that was squeaking (the left one). The whee
... Read more
l had sheared some of the support off and that was the cause of the squeak.
I took the locking ring off and removed the wheel and support. I put the new support in, attached it, and then the wheel, washer and lock ring. I used pliers to push the lock ring onto the support.
Then I put the drum back in making sure it was in all the way (it fits snugly between the wheel and the back of the dryer). The belt is a little tricky to get back on. I put it around the drum and then reached underneath and behind again. The pulley is on a spring, so you have to pull it up and put the belt on all one-handed and blind. Once that was on, I gave it a few turns to make sure everything was working again.
It is quiet as can be now!
I took the locking ring off and removed the wheel and support. I put the new support in, attached it, and then the wheel, washer and lock ring. I used pliers to push the lock ring onto the support.
Then I put the drum back in making sure it was in all the way (it fits snugly between the wheel and the back of the dryer). The belt is a little tricky to get back on. I put it around the drum and then reached underneath and behind again. The pulley is on a spring, so you have to pull it up and put the belt on all one-handed and blind. Once that was on, I gave it a few turns to make sure everything was working again.
It is quiet as can be now!
Read less
Parts Used:
-
Michelle from Kirkwood, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
75 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!