HDB720-05 Hotpoint Dishwasher - Instructions

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

After doing dishes by hand for four months, I decided to take a look at the dishwasher. It took about 40 minutes to identify the problem and order the part fom PartSelect. The part arrived in two days and took two minutes to install. It's best not to rush into these things.

Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Followed easy instructions and completed repair in less than 30 minutes.

Remove the retaining screw in the top of the hub and install new hub in reverse.

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.

part came in the mail and fit the missing space perfectly. no complaints. easy fix.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

Ordered the part and installed...easy and great prices.

I had some extra problems with my water supply line since this is an old house, but I won't dwell on that. If you have an older model like mine (probably 80's) the only trick is with the drain solenoid. The kit uses a newer style solenoid that is a little different. Without getting too technical here, let me just say that if the old solenoid has a little metal lever that is actuated when the plunger goes down do not discard it. From what I have read, the dishwasher will shut down with an error code if you don't use this part and you will also have 2 wires that are just hanging there with nothing to plug in to. You will need to use an included metal plate and screws to adapt that part to the new assembly. It takes a little mechanical aptitude, but after you figure it out it works perfectly. I did not see this mentioned in the instructions but the necessary parts were included. Replacing the pump and motor was fairly simple, and all the needed parts were included in the kit. I did remove the unit from under the counter and lay it on it's back for easy access to the pump and motor. It helps to watch some You-tube videos if you are unsure about how to do this, but make sure they are working on the brand you have. All dishwashers are NOT the same.

with a dishwasher. Someone had 'packed' the silverware basket and there wasn't one in my dishwasher! Ordered one from here, when it arrived, opened the box, opened the dishwasher and placed it in the correct place. Closed dishwasher - DONE!

I googled "dishwasher will not drain" and replacemed drain solenoid. The repair was relatively easy.

nothing to it. slid old one out, slid new one in. however, replacement was not the same model as the original.