Quick Question!

Have you ever purchased from PartSelect.com before?

Models > HDA3400G02CC > Instructions

HDA3400G02CC Hotpoint Dishwasher - Instructions

All installation instructions for HDA3400G02CC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HDA3400G02CC
676-690 of 840
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Faulty Dishwasher Door Latch

  • Customer: cliff from knoxville, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

The unit would not start.

  • Customer: Robert from Riverview, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

Dishwasher very noisy when washing/rinsing

  • Customer: Tim from Alpharetta, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

Would Not Start

  • Customer: JoAnn from Daytona Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.

Dishwasher not completely draining

  • Customer: Courtney from Lancaster, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the video on the website - seriously easy. took me 5 minutes and solved the problem!

Dishwasher leaked badly when running

  • Customer: Kenneth from Lake Bluff, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.

broken rollers

  • Customer: Bruce from Souderton, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
within 5 minutes.Great site for information and parts

Dishwasher was making lots of noise, and specifically rattling

  • Customer: Brent from Fort Collins, CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in the 4 years we have owned the house.

installing new wheels on upper rack of dishwasher

  • Customer: David M from Bonita Springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I thought to myself, this is going to be easy, but I hit a couple bumps getting the end caps off. I just watched the video and it was great and helped me be sucessful. The only thing that would have helped was instructions on how to put the end caps back on! david

The axle rusted through on top tray of tray

  • Customer: william from Canal Winchester, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the tray from its rails. Removed axle clips fro tray and replaced with new axles. Put tray back in rails and I was done. Works like

Dishwasher Was Not Draining - Standing Water

  • Customer: John from Absecon, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed the video on this site, replaced part in under 10 minutes, ran a cycle - p-e-r-f-e-c-t !!! Thank you so much - I am sooooo not a diy type person, but this was easy!

miss wheels

  • Customer: Martha from Fort Worth, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

Lower dishwasher wheels broken/ deteriorated.

  • Customer: Stephen from Madison, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered parts from Parts Select, and replaced lower roller wheels. The diagrams/ drawings were key in ordering the correct replacement parts - thanks

Broken front upper rollers

  • Customer: H. M. from Waskom, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
In the video, they must have been removing new parts from a new machine. 7 year old parts do not come off so easily. You may need a screw driver (I used a plain old dinner knife) to pry up the prong. (Parts went flying as they broke off for good!) I had to use a wrench to get the roller off. BUT, the new part slipped on like "greased lightening." Sooooooo, watch the video, follow their step by step instructions, but be prepared with a tool or 2 since the only reason you are doing this is because it is OLD!!!

Axles on wheels broken

  • Customer: Patrick from Raleigh, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pop the new wheels on. The rear wheels are thinner than the front wheels so rack slides in smoothly
All Instructions for the HDA3400G02CC
676-690 of 840