GTA18AW Refrigerator - Instructions

Installed missing spacer

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Trial and error. IT would have been nice to have instructions with the part. Tried to install the gasket withour completely removing the frame. Wasn't happening. Finally removed the frame and repair went fairly well.

First, I removed everything from the door shelves. Next, I loosened the screws around the door, under the seals, pulled the seals out and slid the new ones into place. It couldn't have been easier. There is no need to remove the door liner. It's like having a new refrigerator.


I was surprised, when my parts arrived 3 days after I ordered them. The cost was less than half, compared to our local parts house.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Exposed evaporator and fan.Turned refer back on. Evaporator started to get cold but fan did not run. Removed fan and applied 115 volts. Fan did not run. Installed new fan kit. Old refer works as good as new. Vary easy job. I almost bought a new refer. Glad I didn't. Probably saved myself $500+ Shopped several sites on internet. Other sites wanted about the same price for motor only and 15-20 bucks more for the fan. Vary pleased that I found this company to buy this part. Received fan kit in just a few days.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

I ordered the post, pulled it out of the box, pulled off the glass, pulled out the drawers. I looked at where the post looked like it shoul go and put it in. put the drawers in, glass on. It took me about 5 minutes and everything is perfect.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

The old piece had broken off, so no removal of the old part was necessary.

New post snapped right into place, no tools required.

Total time for repair was less than two minutes.

with a phillips screwdriver I removed the old handle and replaced it with the new one. Very easily done. The parts I ordered came when I was told they would. The whole experience was a "piece of cake".