Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old gasket leaking
The gasket is sandwiched between the main door and the shelf assembly.
What holds them together is 42 1/4in hex head self tapping screws that run along the edge (each one is finger tight).
I would highly recommend a power drill with a 1/4 hex socket to remove the screws. It makes things much faster. Be careful when screwing the screws back in with the power drill(you only want them finger tight). If the screws are too tight,the gasket will bulge out in places.
At first the seal may feel weak. Keep the door closed for a couple of hours and the seal should improve.
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
No need to repeat the other directions, everyone is spot on with exactly what to do, the ONLY thing I want to add is that prior to putting the new gasket on, throw it into the dryer for a few minutes to make it more pliable..... My problem was that it didn't seat very well, be patient, after 2 days and keeping pressure on it over night, it was a perfect fit !
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
I removed the top door hinge plate and removed the door (it is much easier to do this with the door removed. I put all the food into an ice chest and that made a hardy work area to set the door on and remove the screws holding the inner door and seal. This type of seal requires you to remove the screws completely. Still not satisfied with the way the new seals close, however - the magnet stips in the old seals were stronger.
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
The drawer guide mounts in slots on a bracket hanging below the shelf above. Only had to use a screwdriver to move the plastic tab in the slotted bracket then slide the whole plastic guide out. ordering the new one was easy, cheap, and quick through PartsSelect.com. The new part just popped in without tools. Very easy!
Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.
Old seal was pulling apart, door wouldn't seal tight.
Having 2 people makes the job a snap. On our model the freezer door had to be partially removed so the other door can be lifted off, then slightly tighten freezer door in place. Lay door flat and remove the 36 screws & gasket making sure the new gasket slots are tucked under to match up with screw holes. We started all the screws & came back and tightened firmly. Loosen the freezer door and set the bottom door back in place, make sure doors clear each other and tighten down. Finished! I took the advice of another post and put gasket in clothes dryer for about 5 minutes,helps a bunch. Start to finish,30 minutes. Taking food out of door & replacing.
Picture on grid in website did not match actual size, The length was a little more than half an inch shorter. That meant the hole for the screw did not align. Ordered three different times, two were repeat orders for the same handle, one was for a different model that looked like it would fit. That handle came closer but still the length was too short. Both types of handles did not match the dimensions of the pictures shown. To be fair, I ordered same product from two other companies, Also the same problem. One customer service person said that since this was made in China, maybe converting inches to metric did not translate.