Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time. Steve
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
The firt hard thing was waiting for the part to arrive, but that went quick. The second hardest part was opening the box. Shucks I got a paper cut, should have used a razor but while wife wont let me have sharp objects. Oh, yeah I had to find the hachsaw. I fooled everyone I knew where that was too. Be sure to measure properly, because if you cut too short then you have to stretch the bar. I havn't found any type of bar stretcher that works. It's best if you clamp the metal bar to a 2 X 4 piece of wood in order to steady the metal bar while you cut. You can't cut to well trying to hold the metal bar in your hand. The best part was completeing the job by installing the bars. Finally I have more room in my freezer to store food in the doors. This is my story and I am sticking to it. Have fun.
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
refrigerator stopped cooling due to condenser over-heating
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Bottom shelf retainer, to keep products in, kept falling off causing bottles and other products to end up on the floor.
Tuned up the ends of the bracket with a needle-nosed pliers then installed new retainer clips into bracket. I then laid on floor and lined up two holes in door and bracket (one end at a time) and pushed retainer clips into door's existing holes. Door was open for less than 30 seconds. Bracket is now solid and holding. Note: Do not jam products in bottom or any shelf thus putting pressure on bracket. Find a new home for the product!!
Small Plastic Piece which holds the front metal piece on each interior door shelf was broken
1. Inserted the plastic bracket into the channels on the side of the front metal piece with the hole plugs facing outward. 2. Lined up the plastic piece with the plugs with the holes on the shelf door. 3. Slid the plastic piece (in its channel) towards the door and into the holes.
Broken clip on refrigerator door shelf retaining bar
Easy to replace refrigerator bar retaining clip. Just pop it off with flat tip screwdriver, put the new clip in the bar, slide bar in place till the studs on the clip line up with the holes in the door and pop the clip in place.