GS395LEGB0 Whirlpool Range - Instructions

Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.

Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

Excellent delivery.

Remove the bottom drawer. Remove the two Phillips head screws on the top inside of the door. Pull up on the handle (CAUTION: Be sure to hold the glass front against the door while doing this or the glass front can fall, possibly damaging it. Remove the glass front by lifting it towards the top of the door. Remove the two side pieces and the bottom trim piece by unscrewing the Phillips head screws located on the underside of the bottom trim piece. Discard the old trim pieces. Attach the new metal bottom trim piece using three of the previously removed screws. Do not tighten the screws at this time. Each plastic side piece has a nipple at the bottom. Insert this nipple into the outermost hole at each end of the bottom trim piece. The edge of the flange on each side piece should face inward. Have an assistant hold the two side pieces against the door frame while you slide the glass back in. The inward facing flanges go UNDER the glass. Reinstall the top piece making sure the indentations at the top of the side pieces are under the top piece. Install and tighten the two screws that hold the top piece on. Tighten the three screws holding the bottom trim piece.

No tools necessary. Shipment was extremely quick; I was very pleased.

Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.

We ordered our part from PartSelect.com, of course, using their diagnostic tool(s). We received it very rapidly after ordering (a day or two). It involved taking two screws out of the bottom plate of the oven. There were two screws in the diverter (?), but they weren't attached to anything. I had my son, who is young, strong, and small get behind the oven to locate where the igniter plugged in. He detached it and I unscrewed the nuts holding it in place. One of them was in pretty crooked and made it a little difficult. But I pulled it out. I put the new one in place, my son plugged it in, and I replaced the two nuts, securing the new one in place. I replaced all the parts and their screws while the wife cleaned the gunk from behind where the stove sits. We did perform a quick test prior to re-assembly and it looked good. Re-attached everything, put it back in place and it's working like a dream. Just in time for Fall baked goods...

remove burner - 2 phillips head screws. Raise top - cut wire to ignitor. Strip wires and connect with a wire nut. Drop in new ignitor - reinstall burner.

First time was very difficult I tried to make the panel fit into the frame. Broke both side pieces of the trim.Even thouth I broke the trim PartSelect replaced them. I did not expect that.Second time it was easy. Remove the handle first and then the panel slides into the top and bottom only. It does not slide into the side of the frame but sits on top of it. Thanks, Allen

I broke the old trim when cleaning. New trim kit went together great. No screws needed because of new design. Best tip I can give is that the side trim pieces around the oven door go behind the glass on the door not in front of the glass. Visual instructions would be great.

Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.