Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fastening screws loosened and handle end caps fractured
I dis asymbled the door to access the broken end cap screw holders(plastic) Take great caution with the door glass. It is held in place by thin stamped steel slots and when taking the door face apart, the glass is free to fall out. I placed four strips of adhesive tape on the glass to hold it in place while I replaced the handle end caps. Use an electric screwdriver to place the retainer screws. It speeds up the work, and allows your other hand to stabilize the door. Caution to not over torque the steel screws. They screw into plastic and can strip easy. Another point: These replacement End Caps did not come with any supporting hardware - screws. I was lucky in that I retained the original screws and they were in good condition and could be recycled. Very impressed with the service, would recommend to all. Frighteningly fast delivery. I was shocked to see the box on my porch in just a few days.
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Burner "burned out" so we replaced the one and replaced the other that seemed to be cooling down.
Basically removed the screws holding the op on and removed the vent from back. Just "figured it out" and now it works. Wish I could be more helpful. Recommend moderate experience and confidence.
1- opened oven door 2- unscrewed 2 screws underneath top with a socket wrench 3- unscrewed clips that held burner 4-used needle nose pliers to pull off wire clips off old burner 5- placed wires onto new burner 6- opened clips to make it easier to reinsert burner 7-reattached burner 8-Replaced top
The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
The small burner inside the double burner shortd out.
The first thing was to watch U-Tube . The replacement burner was being replaced in a GE glass top range. Exter tools were required than depicted in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
I did not know what kind of tool was needed to remove the screws so I asked at the hardware store. When i said the screw was star shaped, he sold me torque wrench with multiple heads. First I removed the screw holding the broken handle in place. I cleaned surfaces. Next I attempted to put the handle in place on the horizontal bar and then put the screw into the opening. That did not work. I jiggled the handle for a while but could not get the pegs into the holes. Finally, I just held the handle in place and began to turn the screw and the handle slid into place as the screw got tighter.
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs. plugged in the new element and screwed it in place
I removed the oven door by unlocking the hinges and pulling out. Set on workbench (with towel/pad) and removed handle, four screws, then bottom and inside panel screws, then one nut to finally be able to get at the inner glass insert. Removed insulation and then took an extra hour to really clean all surfaces (middle glass was quite greasy due to inner glass being broken for a while. Reassembly wasn't bad, but took a while to figure out that the two thin 2" red spacers belonged around the two handle screws. This was tough to figure out as they come off when taking the handle off, but you can't see them, so didn't know where they came from! Anyway, if you're just a bit handy, you can do this job.
It was very easy. First turn off the power. Remove two screws to pick up the hood then remove two screws holding the element. Tag the wires with number. Unplug the old burner attach the wires to new burner. Attach two screws with spring to hold the burner, put the hood down and put the screws holding the top hood.
My cooktop is a stand alone unit mounted in a counter top not associated with an oven. -Removed power to the cook top. Breaker off. -Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. This is a two person job preferably. -Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back. -Remove knobs and remove the glass top by lifting straight up. -Record the wire positions on the element on paper and remove the connections. -The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose. -The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this. -Placed the new element in position and reinstalled the spring clips. -Install the wiring terminals in the correct positions. -Reinstalled the glass surface and the six phillips screws. Reinstall the knobs. -Lower the cook top back into its counter top position. -Return power to the cook top. -Installation complete. Very simple!
The dual burnner had somthing drop on it and it went out
I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the burner, then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.
