Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was an annoying buzzing sound coming from the bottom of the stove
I pinpointed the location of the sound, took off the protective plate, felt it vibrating against the plate. I disconnected the power supply, and looked at the wirings and how it was connected, saw some burning residue surrounding the area of the Transformer. Then figured that I could simply replace this. I wrote down the Model and Serial number of the Stove, searched online, found this site. Located the part on the diagram, then simply ordered it. My part arrived in 3 days, and had the part replaced the next day. Couldn't be a smoother fix. Thanks.
Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!
Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.
The oven door would not open properly. The hinges needed replacement.
I followed the instructions per a YouTube video. My older model was slightly different in parts used in the video, but the general idea was the same. Very happy with current repair / parts. The door now opens smooth as glass, and I even got a chance to clean some internal parts inside the door.
The video gave me the confidence to order the part
The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place. Snapped off the top control panel which exposed the wiring connecting the control panel. Unplugged a couple of wire harness units to free the control panel. Be sure to label the units to know which goes where during reassembly. Remove the microwave unit from the housing and place it on its side. Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Oven door hinges sprung on the top oven. This is the second time I've had to make this repair, and I'm wondering if the design may be flawed.
Remove the door. (Two people - the door is fairly heavy). Place on a flat surface to work on it. I used the kitchen island. Disassemble the door to expose hinges. Replace hinges Reassemble door Mount door to oven. I cleaned the door and the face of the oven while I had the door off.
Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.
1. Disconnect AC power 2. Remove back with several sheet metal screws. 3. Remove wires from Limit Thermostat. 4. Check Limit Thermostat continuity -- if open then Limit Thermostat is faulty. 5. Remove Limit Thermostat with two screws. 6. Install new thermostat
Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.
