Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GLTF1670AS0 > Instructions

GLTF1670AS0 Frigidaire Washer - Instructions

All installation instructions for GLTF1670AS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLTF1670AS0
196-210 of 346
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door on washer broke lots of laundry to do!

  • Customer: David from Cos Cob, CT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I was amazed at how quickly my part came for the washer and it came to me on a Saturday

one broken shock

  • Customer: Joseph from Steger, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
when I replaced the other one it was broken also but you wouldn't know it by just looking at it. The only problem being able to get the new one back on I put it on pushing from the front, I can only imagine the ttrouble I'll have get it out again I'll probable have to cut it out with somthing because it's right up against the circiut board housing. other wise not a bad job. But I think my age has somthing to do with it.Not much strength.

water would not shut off causing door to pop open and spill all over the floor

  • Customer: Joe from Interlaken, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.

Water would not shut off

  • Customer: Todd from Eagle River, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reverse of removal.

Front load washer continued to fill with water until door failed. Major Flood

  • Customer: Malcolm from Shelley, ID
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so far!

water dripping into the tub when off

  • Customer: George from St. Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 2 people found this instruction helpful
Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the control panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!

water not turning off

  • Customer: Anita from Orange, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.

No hot water in machine

  • Customer: julie from minneapolis, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
First I removed the hot and cold water supply lines to the machine. Then I removed the two screws at the top of the back panel, and pulled the entire top of the machine off which was a little tricky to figure out. There are two tension-like clips in the front of the machine holding the top on. (I had thought the back panel would come off so I was surprised when it became clear that the top of the machine would come off.) Then I unscrewed the two screws that hold the water inlet valve. I had to remove the green grounding wire that was clipped on the frame. The water inlet valve then lifted out easily. There were two clips to slide off, and a hose going into the tub that also had to come off which I did by loosening a little clamp on the end of the hose- saved the clamp for the new valve! Re-attaching everything was a snap. Tested the hot water before re-setting the top of the machine back together and it worked!

washing machine made loud clunking noise and wouldnt spin on high speed

  • Customer: JEFF from COLONIE, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
First I unplugged. The machine from the outlet then disconnected the two water supply lines from the machine. Next I removed the back panel to gain access to the bottom of the drum. Next I took a nut driver and used it to depress the little tab on the push pin that hold the bottom part of the strut on. After getting the pins out I replaced the old strut assembly withe the new one. I used the nut driver again. But this time I used it as a set tool. Place the nut driver on the end of the push pin and gently tap with a hammer. Until the pin is all the way in. After that I reversed the assembly process to put the machine back together.

Drain Hose Leak

  • Customer: Colby from College Station, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 2 of 9 people found this instruction helpful
Unhooked old hose and replaced with new one.

no final spin

  • Customer: justin from tularosa, NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed top of washer then removed the screws that held the lock in place. only hard part was the lack of room to slide my hand down to get the lock from inside the washer,and put the new one in. managed to find a tech sheet in the washer to put the washer in a "service mode" that is where i could make the washer do a final spin.but it still gave me a code that the door lock was not working properly.(even though it still locked)replaced the lock with a new one and the code disappeared and did a full final spin.. thanks guys

The door strike broke off so the door would not stay shut

  • Customer: Joyce from Mequon, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took off the broken part with a screw driver. I easily found the needed part on your website. After I ordered the part, it came within 2 days. It was the correct part and was replaced within 10 minutes of opening the package. Thanks for the great, easy and quick service!

Replace water inlet valve.

  • Customer: James from Lutz, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a little time consuming. Space was an small issue in the laundry room.

The door on the washer would not lock, therefore, you could not wash clothes.

  • Customer: Sarah from Greensboro, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After some research online about my Frigidaire Washer, I pre-determined that the problem could likely be the lock mechanism. I ordered the part and it arrived within 3 business days. My son removed the screws from the back of the washer, slid the top off and removed the old part and replaced it with the new part. It took about 20 mins. The machine is now working properly again. The door catch that I ordered did not work with the door lock I ordered. However, the old door catch that was still in good working order does work with the new door lock and switch assembly that I purchased.

Both shocks were broken!!!

  • Customer: Daryl from Woodinville, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Everything on the video was fine except when reinstalling the shocks with the plastic pins it was almost impossible to get a hammer back inside to knock in shock on left side and had a plastic part on the right side behind the shock absorber which you could not use a hammer and could pry on that part out of fear of damaging it when reinstalling pin So the video just said the right side just like the left but each side was different in what was located by each side Just confusing meaning you had to be creative in solving them!
All Instructions for the GLTF1670AS0
196-210 of 346