GIE18GTHBRBB General Electric Refrigerator - Instructions

For easy installation I removed the whole shelf that the deli drawer track attaches to, afterwards simply remove the 1 and only small screw, and slide track out, installation is very easy, simply slide track into slot on one end, line up small hole and tighten small screw, it's a good idea to clean the shelf before installation, it looks better and removes and dirt or fingerprints that may have been left behind during installation.

Removal of the original gasket was easy and required no tools. Based on compression in the shipping container, the new gasket was deformed. Using a shallow broiler pan, I brought water to a lite boil. The deformed gasket areas were placed in the water for approximately 10-seconds then placed in cool water. The new gasket came with specific instructions for this task. The instructions provided were easy to understand and accomplished the job

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

removed broken bin , slid new ice bin in closed door. I bought the complete part.

replaced lights in refrigirator and freezer

My son did it , and showed me what he did when he was finished.

On the move-in cleaning of the refrigerator I accidentally broke the glass encased shelf, and I don't believe there was a cover (glass or otherwise) in place that covered the Fresh Fruit and Vegetable bins. Wondering through the internet I found Part Select, ordered Parts 224 and 228. Installation really did take less than 30 minutes including, washing, drying, and placement of the two shelves. It's exactly what was needed. The refrigerator once again looks like a refrigerator with all the shelves in place. The customer service folks were more than helpful. All you need to do before placing the order is look at what you need to replace, write down the the model number, the serial number of your product part needed and chat with the customer service folks. All should go well. I'm happy.

removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.

I pulled the bulb out to see if it was the bulb, no! I took the switch out, of course with the refer unplugged, and jummped out the wires and the light came on. Ordered my switch and put it in in 10 seconds and then there was light! Thanks again for showing me the light!

Tim in NJ

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.

Really simple... broken light switch easily removed with flat edge screw driver. Once removed unplug and plug new one in and good to go.

Replaced the existing shelf without any tools. I had no problems. Thanks Doris