Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
I took the two drain hoses off with the pliers then only two screws that holds the pump. After that the two hot wires which are black and white. But remember to unplug you're washer since the pump is not grounded you don't want to risk being shocked. Hope thi helps. Plus i saved around 250.00 by repairing myself.
I called a repair person to check my 15 months old GE front loader washer that stopped in rinse mode. After his inspection he said it was a deffected computer board and it would be very expensive to replace the 3 computers boards inside and it would be cheaper to buy a new top loader washer. The next day I lifted the top cover and found a taped plastic envelope with instructions titled “For service Technicians Only." On page 2, instruction on to how to enter the washer in to service mode and to test the washer: Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer) Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly. So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
"Door Locked" light always on. Washer would not run
Remove bottom kick plate of washer. Remove 4 screws behind door that hold the latch/lock assembly. Reach up inside the washer from underneath to unplug 3 wire connectors. (This is a very tight spot). Once wires are off, part comes right out. Connect wires to the new part - this is by far the most difficult part of the job because it is way up inside the washer. Replace all bolts. Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.
Two people make the job easier: the smaller on his back doing the work, while the other positions lights and provides tools. Remove bottom panel. Loosen and slide the two small spring clips back from fittings. Locate (out of sight in the back) and loosen the screw-type tensioner on large, upper clamp. Remove old hose and position clamps on new hose. Seat all hose fittings securely and reposition spring clamps. A bit of soapy water for lubrication can help. Tighten down screw tensioner on large clamp. Test by pouring bucket of water into washer.
I followed the steps in the You Tube video on this topic. Search for "washing machine repair - replacing the drive pulley" in your favorite search engine. The video is very well done and it is a simple fix. Before I put on the new drive pulley and nut, I vacuumed up and then wiped down the black dust around the drive pulley shaft (as well as on the inside floor of the washer) to make sure the drive pulley slid onto the shaft using the hand banging method described in the video (dust was likely from the belt due to the excessive movement of the drive pulley). While it may be possible to tighten the nut without a torque wrench, I personally had trouble judging the appropriate 44 ft lbs of torque without it (i.e. my snug required more than a quarter turn per the optional instructions). The torque wrench provided me with the assurance that I installed the drive pulley correctly.Two of my shocks were leaking slightly so I assumed that was the primary issue and replaced all 4 at quite a hefty cost. It helped with the noise but not significantly. If you do have a loud noise during the spin cycle, do yourself a favor and check the play in the drive pulley and look for the black dust before you diagnose the problem to be something else. The online diagnostic tool showed the drive pulley as being the highest probability of being the issue so, sadly, I have no excuses...
Most front load washers have drum rear support (spiders) that disintergrate prematurally
If the washer basket "crashes" or thumps while rotating, the spider must be replaced. I have found that, although difficult, the spider mounting bolts can be removed without sheering if starting to unscrew until it jams then hit the bolt once with a hammer and try again to unscrew. It will give just a little and keep repeating the process until the bolt is completely out. I have tried heating with a torch, chisel tapping and re-tapping the threads after drilling out the bolt but the method I described is the most successful. After removal I bring the spider to a local powder coating person for a permanent coating of preservation. This site provides the least expensive new spiders or spider basket assemblies available. E-Bay provides used items also.
Washer would not turn on without numerous pushes of the power button
Disassembled washer to get access to power board, removed both power and start/pause switches and replaced them with new ones. Reassembled washer. Works well. The most difficult part of appliance maintenance is learning how to disassemble the machine. Videos of the process are very helpful.
Unplug machine. Remove band from front bellows by prying the spring at 6:00 o:clock loose. Pull back bellows on right side. Remove 3 torx screws and gently pull door each lock assembly out. Unplug 3 wire harness connectors and plug into new latch lock in same order. Screw new latch lock in place and replace bellows and band. Done
Loud banging during the spin cycle or when slightly unbalanced.
I watched the video and followed the advice given. It was very easy fix to the annoying problem of the banging wash tub during the spin cycle. The part worked perfectly so far so good.
Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.