Models > GFS185/MN10 > Instructions

GFS185/MN10 Caloric Refrigerator - Instructions

All Instructions for the GFS185/MN10
106 - 112 of 112
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Evaporator Would Freeze Up And The Food Section Could'nt Cool
I just followed the enclosed instructions
Parts Used:
Defrost Timer
  • michael from buchanan, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Clothes were not getting dry enought
Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"
Parts Used:
Dryer Radiant Flame Sensor
  • Michael from Royal Palm Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
fan motor did not run all the time
unpluged refrigerator. removed panel in front of fan. Removed the fan motor. Installed the new fan kit. Replaced the panel in front of fan. Pluged the refrigerator back in. The refrigerator runs a 100 percent better
Parts Used:
Evaporator Fan Motor Kit
  • Charles from Marion, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
not cooling
R/R part, 3 screws reconnect 3 wires. easy.
Parts Used:
Cold Control Thermostat
  • Ted from Crestline, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat
I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.
Parts Used:
Dryer Radiant Flame Sensor
  • Steven from Oak Lawn, IL
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Evaporator fan motor stopped working
Remove back cover of freezer compartment; Remove old fan assembly, new fan terminals did not exactly match old one so I had to remove one of the terminals from old fan and attach it to new fan/ then install new assembly and repaced freezer cover
Parts Used:
Evaporator Fan Motor Kit
  • Kurt from Baltimore, MD
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
How to get timer out of defrost cycle?
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Parts Used:
Defrost Timer
  • David from Virginia Beach, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GFS185/MN10
106 - 112 of 112