GFS165/MN02 Caloric Refrigerator - Instructions

I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

tested all limit switches with electrical meter to see if they were bad. All switches tested and ohmed out fine. then looked in and saw a hot serfice ignitor and went right to the problem. I have been a furnace man for some time which would give an advantage over the average do it yourselfer. Once I found the bad part and checked resistance across the element, I instantly went on line and ordered the part.the part came in one day and it was the exact part nothing generic, put the part in and was drying clothes again in only two days. Thankyou so much and I hope to get another 5 yrs of drying clothes out of this appliance. Jim P.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha comes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.

removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...

1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. Replace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.

Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.

After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.