Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burnt out burner
Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.
the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.
To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.
Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.
After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.
Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!
I turned off the range breaker and doubled checked to make sure the power was off . Using 1/4" ratchet wrench I removed 2 sheet metal screws and lifted the glass top up and held it in up with a small cardboard bow. I removed 2 more screws holding the element in place and installed new unit. I then
dropped stove forward, handle broke and trim around it also broke.
Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle. Finished! Replacement parts fit perfect!!! Thanks a milliion!
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.
Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.
Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate. This was an easy fix for a seventy year-old like me!
Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.
back R burner of ceramic top stove went out - died
1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!
only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!