Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door chute broken
First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.
One finger of the spring steel peice that holds the ice maker and water dispenser levers out broke.
I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix. I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites. Thanks, Ron
The black plastic or teflon coating on the ice mold was coming off in flakes and freezing in the ice cubes
I took out the ice collection box and auger to get access to the three screws holding the ice maker assembly against the left wall of the freezer. You can use a screwdriver or a nut driver. I then unpluged the assembly and wiggled it loose from the water fill tube. I assumed that unplugging the unit would disable the water valve but I put a plastic tub under the fill tube just in case. I studied the assembly on the kitchen table for a few minutes before I disasembled it. After removing a snapon plastick cover I removed three or four screws on the gearbox and was able to pull and wiggle the parts apart. The heater contacts have rubber O rings so you have to be firm pulling the mould out of and into the gearbox mount. Make sure it is fully seated. On reassembly note that the ice kicking arm is notched so it fits into the gearbox only one way and it helps to have it in position when you screw the gearbox back on. I also found the plastic ice guide that fits on top of the mold a little awkward in snaping back together. Make sure its fingers space evenly with the ice kicking arms.
Ice maker mold was cracked and leaking water into the bin which then froze all the cubes together.
I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.
It was SOOO easy, I turned and popped out the old filter and turned and snapped in the new one....I don't even think it took a whole minute to replace!!
My ice maker stopped producing ice. It would dispense ice that was already made and the water dispenser worked.
I looked at some online diagnostics info and the owner's manual. The "error code" blinking red light on the receiver unit (located adjacent to the ice bucket) indicated that the emitter/receiver units were faulty. I located the parts on the PartSelect website (their price was less than half of what they wanted on the Sears website) and ordered them. I didn't pay for the expedited shipping and still received the parts within two days of ordering. Powered down the refrigerator, three simple screws to remove each cover for the emitter and receiver, unplug the old units and pop in the new units, replace the covers for each unit, repowered the fridge and, voila, you've got ice. I completed the repairs in less than 10 minutes. Couldn't be happier with the price, the diagnostics links/info or the prompt service. Next time I have an appliance issue, my first stop will be this website.
The light switch on the refridgerator broke - no light.
Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.
The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.
The slides fit into the slots of the self metal, but couldn't be pushed forward to lock into place! At first I tried to put the slider in by hand, but it wouldn't snap in place no matter how hard I tried. A friend also tried to get the slider into the slots and push forward to lock in place in the metal part of the shelf. No go! It took a while, but I figured if I used a hammer to tap the slider into place that might work. It did. It would have been helpful to have some instructions on inserting the slider, such as "use a hammer tap the slider so it locks the slider into place". You just can't do it by hand! Other than that, it went really well and replacement then only took 1 minute. . .instead of the 30 minutes it took to try to lock the sliders.
Refrigerator indicated that water filter needed replacement
It took less than 5 minutes to remove the old filter and install the new one. Push a button and the old one pops out, stick in the new one, and you're done.
I removed the Ice door front cover on freezer door. Found door pivot was broken. I installed door pivot bracket, and dashpot in kit. I used most of the kit to repair it. The door now works like new. Thanks for the right parts Frank
The part to fix this was a $50.00 part. I purchased this Bracket Dispenser for $6.00 and it fit on My fridge perfectly. I just used the screw hole that was a little higher on the water dispenser. Simply cut off the broken end / or Buy a new Hose (Cost at Lowes about $6.00) guide hose along the bracket and use a socken set to reinstall the screw. Water is not squirting on people any more.
At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.
Looked at repair diagram, ordered part [ fast shipping ],first empty freezer pulled everything out removed rear panel, removed motor, installed new motor into housing. Using a heat gun [on low ] defrosted ice build-up on coils, this tookover one hour , reinstalled everything and it started right up but took 24 hours to stablize and get the ref / freezer back to the -10/37 degree . All better and quiet now. Last time I paid for the repair over $200 very happy thank you part select
