GBS277PDS5 Whirlpool Wall Oven - Instructions

Oven stopped heating after attempting a self cleaning cycle. Problem turned out to be failed thermal fuse component. This is an easy repair and well worth the attempt given the replacement cost of the oven.

First step was to locate and shut off the two circuit breakers supplying power to the oven. Then I locked the panel to ensure someone didnt re-engage the breakers while I was working on the unit. (Lock out / Tag out).

Second step was sliding the oven out of the cabinet - this unit is located below a cooking top and was just the perfect height to allow a furniture dolly to be used to support the oven as I slid it out.

The unit is 'hard wired' (i.e. no power plug) so it can only be pulled out so far from the cabinet, but there was sufficient reach to allow access to and removal of the sheet metal cover at the rear of the oven to expose the thermal fuse and the read wiring. I proceeded with care, assuming the power was still on and once the terminals of the thermal fuse were exposed I performed a voltage measurement to ground on each side of the fuse to ensure power was in fact off.

Then I used an insulated pliers to gently remove the wire harness at each side of the fuse, and once the wires were removed I performed a continuity check of the suspect fuse, and confirmed it was an open circuit (i.e. failed).

Removal of two more screws allowed the fuse to be removed and the new fuse was installed, reversing the procedure.

This was followed by replacement of the rear sheet metal and finally sliding the oven back into its place in the cabinet using the furniture dolly. This is a single oven but still very heavy and has some sharp sheet metal edges likely to cause cuts if not handled with care so the dolly and a second set of hands (and good gloves) are nice to have.

Finally, after inspecting the oven door gasket and other air vents around the outside of the oven to identify suspect causes of the overheating event that tripped the fuse, the air vents above and below and within the door were cleared of dust-bunnies and other debris that had collected, possibly causing interference with the air flow that cools the area in between the oven and the cabinet. This blockage may have been the root cause of the fuse failure - i.e. the air did get too hot back there and had the fuse not tripped it would have been dangerous. The door gasket looked fine although its also an easy replacement and does not require oven removal.

The new part fit perfectly - it was a different design than the original part that shipped with the oven but appears to function perfectly so no complaints. The trip temperature is identical to the OEM part based upon the nomenclature on the back of the OEM and the replacement fuse part.

Unlocked the power panel and turned on the two breakers to the oven, set the clock and checked operation and its functioning great now.

Have not run a self cleaning operation since the repair but that is the next step and now that those door vents are clear I suspect that the fuse wont trip again.

Lesson Learned: Check those vents for obstructions.

Similar oven selling at discount because its the end of the model year is now priced at over $1100. Fixed our unit for $50 and the added cost of a $20 furniture dolly that I already wanted to buy.

Give this repair a try its a piece of cake and well worth the effort.

Used a Phillips head screw driver to remove cover that was covering the over bottom 1/3 of the installed gasket. I then used flathead screwdriver to help remove gasket from the "pins" that were in the gasket that held it to the oven. Installed new gasket inserting pins into the oven. Then I installed cover over bottom 1/3 of gasket. Overall process was very easy

Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and connector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install

The website and diagram of my oven helped me know exactly what was wrong and where to locate the problem. I simply removed the oven door and the trim, pulled the oven out of the wall. After removing the back panel I located the part and put in the new part. Then reversed the procedure.

First we had to take the oven door off, which proved a bit tricky. There was a release pin which was hard to find and release. Then we had to unscrew the screws and take the glass and inside of the door off to access the spring hinges. Replacing the hinges was pretty easy, as was reassembling the door. The door snapped back into place and voila! the door stayed shut.

Removed the door and laid it flat with the cracked glass facing up. applied duct tape to the broken glass to help hold it together. Removed the screws from the frame holding the glass. lifted the frame off,removed the broken glass and replaced it with the new piece. replaced the frame. and put the door back on the oven.

Turned off breaker to oven. Removed 2 screws, used pliers to remove 2 wires from old element, replaced with new part, connected wires to new element and screwed in 2 screws. Turned on breaker, then oven and new element heated. Very easy!

Replaced the lower heating element with a new part.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Scarey> First thing you should do is cut off the electricity at the main breaker box. I dam near blowed myself up. It's 220Volt I found out after all hell blew up in my face. I was lucky and didn't get shocked.I shorted out the old broiler element.

So I made the job real easy I called a professional to come install the new broiler element.

I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.

Gas Oven would not work without door shutting all the way. New hinges fixed the problem! Removing Superba oven door was the challege. Kitchenaid has their manuals available online which you can look up using the model # available on side of oven door. It contained instructions for door removal which required two pins (one in each hinge) inserted in the hinge holes for the door to release when you pull up and out on it. Nails may be used to replace the pins but the tricky part is removing the nails from the old hinges to remove them from slots in oven door. I used a 12 inch piece of small PVC pipe as a lever, inserting the pipe on the exposed portion of the hinge. This released the nails. The oven door must be taken apart which required removal of screws on the inside face, top and bottom of oven door. It went easily back together and the problem was solved.

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

1- TURN OFF POWER TO OVEN
2- REMOVE OVEN
3- REMOVE BACK PANEL SHROUDING
4- DISCONNECT POWER TO BLOWER
5- REMOVE BLOWER UNIT
5- REPLACE WITH NEW UNIT
6- RECONNECTED POWER
7- PUT OVEN BACK

Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem