GBS22KBSCWW General Electric Refrigerator - Instructions

Installing the part repaired the fridge and freezer immediately.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Replaced Temperature Sensor and now it is getting cold.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Easy

The center peice was the hardest part to take out. Had to be very careful to not break plastic. Also the two front slides where just as bad. to much plastic and to me its totally junk plastic. The drawers ride on these plastic guides and the are very thin. Also, NO supoprt in the center like the older models. The drawers sag in the center.

Removed broken part from refrigerator.
Removed 2 plastic parts and tempered glass shelf
and installed on new part.
Change out went OK.
A few tools and some patience

Job complete

look at how part was in before you take it out - I didn't and it took me three times longer!!!

Replaced thermodisk (Fuse-M). Did not solve the problem. Found Burn Mark on Mother board. Replaced Motherboard. Freezer still frozen. Waited 17 hours never defrosted. After 17 hours defrosted freezer and now waiting to see what the refrigerator is going to do about defrosting. There is continunity through the thermodisk and the defrost coil.

The seal was replaced but the unit has not improved. Troubleshooting - the heater unit on the coil at the freezer was checked; OK, But; there is a little ice build up on the upper area of the condenser. The compressor is running, the lower aft section of the fan and coils is clean and operating. Changed sensors on the freezer and upper fridge compartment. Still no help. May just purchase another refrigerator..:(

followed part select video instructions