GBD277PDS09 Whirlpool Wall Oven - Instructions

Removed locking device

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.

We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

unscrew cover
remove old bulb
screw in new bulb
replace cover

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Simple - Removed oven door attached retainer with screw.Re attached door.

Whirlpool wanted three time the cost of the same parts The only shipping option was Fedex Overnight which was very costly.

Your prices are great "Parts Select".

Jan

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.