All Installation Instructions for Maytag Range GA3277XUAM

The oven bottom was warped and could not be positioned properly in the oven.

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

Parts Used:

Oven Floor Panel

Tara from ALBANY, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Simply remove and install new parts

Overall, it was painless and easy with zero problems

Parts Used:

GRATE BURNER

Jacob from LITTLE CANADA, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced upper over light and assembly

I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.

Parts Used:

Light Assembly

Thomas from SAN DIEGO, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Racks were old

Replace the racks. No special instructions.

Parts Used:

Oven Rack

Sandra M from DISTRICT HTS, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

Parts Used:

GRATE BURNER

FRANCES from AFFTON, MO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old Valve Knob Broke at Base

Simply pull off the old knob from the stem, then push the new knob onto the stem. NOTE: This part works for the POWER BURNERS on the Maytag MGR4450ADH - the stems and knobs of the regular burners are different.

Parts Used:

Valve Knob

Michael from HILLSBOROUGH, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

1960's oven door gasket fell apart, actual gasket not available any more

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

Parts Used:

Door Seal

Mary from WINCHESTER, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My oven door seal had dried rotted

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Parts Used:

Door Seal

Anita from ELKTON, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.

Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.

Parts Used:

Door Seal

Mz from COLUMBIA, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original rack had melted plastic on it.

Removed the original rack. Checked dimensions, installed the new rack.

Parts Used:

Oven Rack

Linda from BURBANK, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

original fixture required bulb - this fixture (all-in-one) was great

Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.

Parts Used:

Light Assembly

wesley from ODENVILLE, AL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Thermostat bulb was hanging loose

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Parts Used:

Thermostat Clip

Willi from Old Saybrook, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used: