All Installation Instructions for Maytag Range G3227XRWM4

Leaking gas from sides of burner

Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.

Parts Used:

Burner Head Cap with Spark Electrode

Homero from SEAGOVILLE, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken burner - easy fix

The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to replace. Without problems it should take about 5 minutes.

Parts Used:

Burner Head Cap with Spark Electrode

Don from NEW YORK, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I needed a broiler pan

I took the broiler pan out of the shipping container and put it in the oven.

Parts Used:

Broil Pan Insert

Broiler Pan

Rhoda P. from Secaucus, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken burner knobs on stove.

Just replaced the old burner knobs with the new !!!

Parts Used:

Valve Knob

Barbara L. from Tewksbury, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Install valve knobs

This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.

Parts Used:

Valve Knob

Donald from Peebles, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

my knobs were broken on 30 year old range

I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.

Parts Used:

Valve Knob

Larry from LAWTON, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced upper over light and assembly

I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.

Parts Used:

Light Assembly

Thomas from SAN DIEGO, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Racks were old

Replace the racks. No special instructions.

Parts Used:

Oven Rack

Sandra M from DISTRICT HTS, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner igniter problem.

Replaced with a new one.

Parts Used:

Burner Head Cap with Spark Electrode

Dhirajlal from SKOKIE, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

original fixture required bulb - this fixture (all-in-one) was great

Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.

Parts Used:

Light Assembly

wesley from ODENVILLE, AL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Simply remove and install new parts

Overall, it was painless and easy with zero problems

Parts Used:

GRATE BURNER

Jacob from LITTLE CANADA, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The oven bottom was warped and could not be positioned properly in the oven.

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

Parts Used:

Oven Floor Panel

Tara from ALBANY, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

Parts Used:

GRATE BURNER

FRANCES from AFFTON, MO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

1960's oven door gasket fell apart, actual gasket not available any more

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

Parts Used: