FX710BGS ((XAC)(0002)) Samsung Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating and holding temp
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the center of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
Parts Used:
-
John from EAST QUOGUE, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
13 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
REPLACED THE FLOOR CAVITY
REMOVED THE TWO SCREWS AND THEN THE FLOOR PIECE. THEN REPLACED THE NEW FLOOR CAVITY AND SCREWED THE NEW ONE IN PLACE.
Parts Used:
-
Madeleine from CHICAGO, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat consistently
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
Parts Used:
-
Steven from CHEYENNE, WY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven igniter burned out
Took out oven racks and bottom steel plates, unscrewed old igniter and replaced with new one, only problem was plastic connections were different so I needed to strip wires and use wire nuts. Very easy fix that anyone could do..
Parts Used:
-
Wayne from PLEASANT VLY, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element needed replaced
First we unplugged the oven and shut off the gas. We then began removing the two plates on the floor, inside of the oven, to reveal the pipe with the dead heating element. You remove the screws from the back of the first plate, pop it out from the front, then remove the screws from the front of the second plate and pop it out from the back.
The only issue we encountered was when we attempted to remove the two screws for the pipe: the front screw was stuck (possibly from old oil) and stripped easily. to fix that, we took a metal handsaw, and sawed a new cut into the screw to fit a flathead.
After dealing with the screw, we removed the pipe and unplugged the old heating element. We removed the bottom drawer for extra room to assist with unplugging the heating element, and for removing the pipe from the gas line.
We removed two screws with nuts that were attaching the element to the pipe, and replaced it with the new element.
after reattaching the element and placing the pipe back onto the line, before we placed the plates back, we turned the oven and gas back on to test if it was working. One successful test later, we placed the plates and bottom drawer back and we were done.
The only issue we encountered was when we attempted to remove the two screws for the pipe: the front screw was stuck (possibly from old oil) and stripped easily. to fix that, we took a metal handsaw, and sawed a new cut into the screw to fit a flathead.
After dealing with the screw, we removed the pipe and unplugged the old heating element. We removed the bottom drawer for extra room to assist with unplugging the heating element, and for removing the pipe from the gas line.
We removed two screws with nuts that were attaching the element to the pipe, and replaced it with the new element.
after reattaching the element and placing the pipe back onto the line, before we placed the plates back, we turned the oven and gas back on to test if it was working. One successful test later, we placed the plates and bottom drawer back and we were done.
Parts Used:
-
Danielle from GIG HARBOR, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My husband tried to cook and spilled something on the bottom panel that burned. Then he tried using a metal paint scraper to get it off, only he took off most of the enamel.
Just had to unscrew 2 screws to remove the old one and replace with the new one. Very easy
Parts Used:
-
Roberta from CHESAPEAKE, VA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Slider Assembly in Oven Warming Drawer
Install handled by building engineer...thankfully. Did not take long for him, however, to install both sides of the drawer.
Parts Used:
-
Judith from WASHINGTON, DC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't light
1) Remove oven door
2) Remove oven floor with Phillips screwdriver.
3) Remove igniter with screwdriver and wrench
4) Remove bottom burner
5) Install new igniter to burner
6) Replace burner
7) Replace oven floor
8) Replace oven door
9) Test
2) Remove oven floor with Phillips screwdriver.
3) Remove igniter with screwdriver and wrench
4) Remove bottom burner
5) Install new igniter to burner
6) Replace burner
7) Replace oven floor
8) Replace oven door
9) Test
Parts Used:
-
Timothy from WASHINGTON, DC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!