FRS26KF6EMB Frigidaire Refrigerator - Instructions

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

Removed the Plastic Cover at the top of the door. (One Phillips Screw ) Removed the Hex Screws with socket set. Lifted EMPTIED door off bottom hinge. Pulled the broken bearing out with needle nose pliers. (Very Easy!!!) Placed new bearing into slot and reversed the procedure. 15 minutes tops. I spent more time cleaning the door and gaskets than replacing the parts. Funny thing, I called the local appliance parts store and they stated this is a common problem. However, for such a common problem, they didn't carry the part and it would have cost more than what I paid here. Additionally, I paid for 3-5 day delivery. Part was here in 2 days. Awesome!!!! I'll always come here first for all my parts needs. A+++

The old support just unscrewed & then the new one screwed right on with two screws.

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

I just took the old filter off and replaced with the new one, after I run the water for about 15 minutes and tossed the old ice and cleaned the tray.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

Ordered new water filter. It arrived, I opened it and took out the old one and put in the new one. I worked perfectly
as soon as I realized I had to remove the protective caps.

First removed food from the refrigerator door.

Second removed plastic cover plate and metal plate assembly from top of door.

Third lifted door of metal pin on bottom.

Fourth removed broken closer plate and replaced
with new closer plate.

Set door back in place.

Re secured the metal plate and plastic cover plate.

Replaced the door shelves and food. DONE.

First I removed one screw holding top hinge trim in place. I than removed two screws holding top hinge from refrig. I removed refrig door and laid it on a table. I than removed two screws holding the door stop and bearing hinge. I replaced the defective parts and reassembled in reverse order. Simple 10 minute repair.

put the new ones

I remembered to unplug first. took the little cover off on the bottom, unscrewed the 3 screws. then just held the base that the fan is on and pulled rite off, pushed the other one rite on. it took me five min, i want to say thanks to parts select, had the part, fast shipping, great job, thank you.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

pushed release button removed filter, installed new filter