FRS24XGCW1 Frigidaire Refrigerator - Instructions

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Ordered gasket and gasket arrived within 48 hrs. Put the unit into out-of-commission status. Defrosted cooling coils. Dried the coils thoroughly. Reinstalled cover panel to the coils. Removed existing door gaskets. Installed new (2) gaskets. So far ice buildup to the coils had ceased.

Wasn't sure if it was the derost timer or the heating element. Since the timer was much cheaper, I bought it and crossed my fingers.
My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring.
Success! My coils no longer freeze up.
Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.

Removed old thermostat and replaced. really easy.

I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!

We replaced the water control valve. We took the old one out and put the new one in. We primed it and then it took off.

I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.

First I remove the back panel which had 4 screws. Then I removed the ice maker. The icemaker is held in place by the 2 screws that requires backing the screws out just a litter, than lift up and remove the electrical connector. Used a volt ohm meter to check the resisitant in the heater element and the defrost timing switch. Both tested good and that left only the thermostat. Removed and replaced the thermastat swich. I cut the ends of the old switch and crimp the ends of wire with the crimps that came with the swict i purchased from parts select. My refrigerator is working properly and making ice like normal.

I could not believe just how fast my order came to my house! The drawers fit perfectly..just like the old ones.

I would highly recommend your company.

Thank you for having the right part for my refrigerator and the expedicious delivery of my order.

the first purchase was the drawer support. that helped, but in the process of replacing the support, we noticed that the drawer was also broken. bought the drawer and a roller that we had inadvertently thrown away with the broken piece of the support.

used a screwdriver to replace the roller. delivery was terrific. the parts fit. nice job.

tested defrost timer and heater. And then tested defrost timer with ohm test($6 at hard ware store) Closed and would not open replace and tested freezer take 30mins to get switch cold and retest.

Replaced drawer slide, R&R two 1/4" hex head screws, 5 minute job. Door handles required phillips screw driver, simple once I figured out trick to upper and lower moulding re-install. Need to remove plastic clips from doors and insert into mouldings, then slide mouldings over new handle ends and snap into place.

First of all I got the part in less than 24 hours without paying any extra shipping, great service.
The part was easy to install, removed 2 screws and 2 plastic water lines, disconenected water line from the sink (turn off water first) and put in new part took less than 30 minutes and is working perfectly.

Removed four screws at top and two at bottom and pulled ice maker unit out and replaced with the new lever .

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.