Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator light was out
Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.
The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.
Project requires removal of 9 phillips head screws. Also have some needle nose pliers and a paper clip and/ or skinny magnet handy for steps (7) and (9).
(1) Turn off power to refrigerator. (2) Slide out water catch tray at bottom of dispenser unit. (3) Remove the three screws that are now visible. (4) Pull front water/ ice dispenser (cosmetic) panel off of the refrigerator and set aside. (5) Remove the 3 screws affixing circuitry panel in place and set aside. (6) Gently pull out the circuit panel and allow it to hang from the refrigerator door. Note: Unless you have very large hands you should not have to disconnect any wiring to do this repair. (7) Remove the three screws and two plates holding the dispenser actuator in place, being careful not to drop the screws or plates into the unit. If they do drop you can get them out of the unit using the needle nose pliers and/ or a bent pointy piece of metal (e.g., paper clip). (8) Remove broken dispenser arm. (9) Insert new dispenser arm. (10) Replace all screws and panels. (11) Turn refrigerator power back on.
Note: The new dispenser arm has reinforcing bars molded into the back that were not on the original model. The company is apparently aware of the problem of the weak dispenser arm and fixed it in the replacement part... so, you should not have to be doing this repair again.
Removed (unsnapped) plastic cover from back of refrigerator ( inside freezer compartment), determined that the fan was not turning, removed 4 screws from the aluminum back plate in freezer and tilted it down. Removed 2 screws with a nut driver, this allowed the fan to be removed, unpluged fan motor from the bace of the freezer and removed fan. Installed new motor and spent $38.00 to repair the refrigerator that would have cost me severial hundred dollars to replace. Thanks for the help
The bottom of Refrigerator would not get below 48 degress. Freeezer was working fine.
First I unplugged fridge. I then removed cover that keeps fan protected. I then removed 2 screws that hold the evaporator motor in place. I then removed 3 wires running to motor. Very easy to remove, just pulled connections apart. I then replace the old motor with new.
The Sears repairman wanted to charge me $359 to repair. I did repair for under $40! Amazing what you can save if you have the time and knowlege to do it yourself.
Water in the ice bin freezing all the existing ice into clumps
You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2) 1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.
Snap out fan cover, remove four 1/4" screws, remove back cover, remove defective fan motor, remove fan blade, install new motor and blade, strip wires and hook up with wire nuts, reinstall back cover, snap in fan cover, and plug in fridge.
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.
first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered, the fan would come on because the board was fried. it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together. evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts
- Unsnapped old light socket from top of Frig - Disconnected elect wires - Reconnected elect wires to new light socket - Snapped new socket in place - Done in less than 2 min.
Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation
Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unplug the appliance first before opening the cover. Remember safety first.)