Parts That Fix Frigidaire Range FGGH3047VFB Gas igniter glows, but will not light
Gas igniter glows, but will not light is a commonly reported symptom for the FGGH3047VFB Frigidaire Range, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FGGH3047VFB Frigidaire Range that will fix Gas igniter glows, but will not light.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Ratings submitted by customers like you who bought this part.
The oven burner igniter simply ignites the gas so it can heat the oven burner. The igniter does this by drawing electrical currents through the oven safety valve to open it. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. You will need a wire splicing tool to do this repair. First, disconnect the wire harness from the igniter by removing the access panel on the rear of the stove. Next, access the front of oven and take out the racks before removing the bottom of the oven. For the rest of the installation instructions refer to the diagram provided by the manufacturer. Remember to unplug your oven from the power source before beginning this project.
$130.98
In Stock
PartSelect Number PS2364063
Manufacturer Part Number 316489403
Replacing your Frigidaire Range Oven Bake Igniter
Customer Repair Stories
Oven would not heat up
Tore the oven apart and replaced the igniter, then put the oven back together. Perhaps if Frigidaire manufactured an appliance that lasted longer than three years this wouldn't have been necessary. This is the second Frigidaire range that only lasted three years. Believe, the next stove we buy will definitely not be a Fridgidaire!
Charlotte from ROCHESTER, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
9 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stovetop worked, oven did not.
First, remove the warming drawer. This allows access to the igniter's plug. Unplug the igniter. The rest of the job is performed within the oven. Remove the bottom (1/4 inch socket). Then remove the next, v shaped piece. The igniter is bolted to the aerator. Remove bolts, and it pulls right off. Reverse these to install new igniter.
Ratings submitted by customers like you who bought this part.
This igniter has a short wire harness. The wire length is approximately 6 inches long.
$89.20
In Stock
PartSelect Number PS11770500
Manufacturer Part Number 5304506545
Replacing your Frigidaire Range Broiler Igniter
Customer Repair Stories
replace bad oven ignitor
Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to
... Read moreplug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..
Ratings submitted by customers like you who bought this part.
This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.
$47.25
In Stock
PartSelect Number PS1528542
Manufacturer Part Number 316490000
Replacing your Frigidaire Range Temperature Sensor
Customer Repair Stories
oven temp not consistent with setting
took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.
john from spring, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
68 of 150 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven did not heat up
Replaced the probe because that's what this site recommended.The oven still does not heat up.
Tim from ASHAWAY, RI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
68 of 103 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
