Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
frost and ice build up/ gasket wasnt sealing properly
I did watch a repair a utube video which I asked for when ordering. Pretty much followed most of the directions but:
started in left corner an lossed all screws from left to right. took off old gasket in small sections and inserted the new gasket and semi tighten screws
proceeded down left side then right little by little as above. to get to bottom of door.
bottom corners were a little snug to get them into place. the last corner was snug but once connected. tighten screws not too tight. You dont want to strip them.
test door with piece of paper.
if paper is not a snug tug, you can adjust gasket with a hair dryer set to low.
it was easy. freezer is all set.
Partselect was great to deal with, support verified the part number was correct for my freezer and help with that video.
freezer would frost up and not get cold enough to keep frozen.
Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.
First, unplug the cord, open the freezer door then unscrews 6 screws of the back cover inside the freezer. Replace the defrost thermostat. Second, on the back in the bottom you'll see the controller which connects to the compressor then unplug the wire to the controller and use a screw driver to take the controller out and replace with the new ones. That's it. Most of the time you just replace the defrost thermostat, but in my case I did try only the defrost once but it didn't work that's why I have to replace the controller too. Now it is working fine.
Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on. Reattach back panel. Put shelves back in.
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker. 2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,. 3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket. 4.Now take out 8 screws that hold the back panel in place and remove the back panel. 5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Very simple - removed the plates that cover the end of the handel, then removed the screws and the broken handle. There were four screws - did a top one, then a bottom one, then the other top and bottom one. Made sure they were on tight and put the covers back on. Really proud of myself!
Cooling coils would ice up and fridge would warm up
I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.
Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!
My Freezer Was Frosting Up, My Ice Maker Was Not Working ,And My Fridge Was Warm.
Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.
Lost all the food. Cleaned out the insides. read some Q and A on this freezer online. Took apart the inside panels...found the schematic on the back corner of the freezer. Eliminated the themostat and fan as the problem. Located online the manual as my wife lost the original paperwork. Gambled the control unit was the problem. Ordered it. It arrived ontime. Installed it. Freezer ran. Put the freezer back together. The thermometer I bought a long time ago said it was at 30 degrees below zero. I adjusted it up to 20 below and it has been running great. Thank You.
removed the screws/nuts; pulled the back panel off, removed the old thermostat (wires just popped apart) replaced the new thermostat (wires just popped back on) replaced the back panel and the nuts and TaDa!!