Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No Water Circulating in Wash or Rinse Cycle
Removed the dishwasher from under the counter, and ran to diagnose the problem. Drain pump ran, but circulating motor did not. Ordered the replacement circ pump / motor assy, and slid the washer back in its hole. When the new motor arrived, I slid it back out, disconnected everything, and drained the water from the bottom. Then I tipped the washer on its side, removed the old motor and installed the new one following included instructions. I did have to use the new wiring harness, and found the new one had only two leads where the original had three. I connected the blue and white leads, and left the original green loose. All in all, it was an easy repair that could be done by anyone with a basic set of skills.
First turn the power off! If you have water in the tub, use something like a wet/dry shop vac to drain as much water out as possible. Removing the strainers will help get more out. To remove the smaller horseshoe shaped strainer, pull up and towards the handle. The sprayer is then removed by rotating the base of it slightly. Then you can remove the large strainer. The more water you get out the better! Then remove the kick panel. You will see the drain pump right in front of you with a white and a purple wire. Disconnect the wires by pulling their tabs towards you, and move them out of the way. With a screwdriver, loosen the worm clamp on top of the pump that connects the drain line to the pump. Have a towel handy, even if you got all of the water out, there will still be some in the line. Then take a pair of pliars (long nose may work best, or small channel locks) and compress the clamp on the black hose behind the pump, moving the clamp towards the center of the hose. The pump should now move a little. Pulling the pump towards you, wiggle slightly to try to remove the pump from its support, preferably without breaking the tabs, but keeping them intact is not critical if you are replacing the pump. More water may come out at this point, so be prepaired. Put the new pump in by reversing the process, making sure you do not break the support tabs. Slide the compression clamp into place. Reconnect and tighten the drain line, reconnect the white and purple wires. Dry your work area carefully so you can spot any leaks. Apply power, and run a rinse cycle, watching for leaks. If everything looks ok, kill the power again and reattach the kick plate. Turn power back on one last time, and enjoy your dishwasher again!
The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job
unscrewed front panel..then removed old latch and put one lead at a time on new latch so as not to get confused..( I did not unplug washer) replaced new latch installed panel..done..Less than 30 min
Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.
the pump was making some loud noise so i removed the bottom cover and the drain pump is right in the front the motor was hot the washer had water on the bottom so i started the washer hit the pump with a screw driver handle to get it started drained the water and used pliers to in still. not bad at all.
upper arm kept coming off and leaking at bottom of dishwasher
unscrewed the old upper arm spray nut off and rescrewed the new one on....very easy...then I took the old gasket out of the bottom of the door and replaced by sliding it in. very simple....less then 15 minutes for both and have solved my issues.
Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks
Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!
I unscrewed and removed the old Arm-Control fixture. I had a little (very little) trouble figuring out how to fit the gasket. It didn't go on like i thought it should. There was no gasket on the original fixture. So I put it on the way I thought it should go. I then screwed the new Arm-Control fixture on to the outlet. That was it. No tools required.
DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.
Removed bottom front dress plate and ran dishwasher. Noted there was a major leak from pump. Went to website parts list located part and ordered online. Once part arrived removed dishwasher from counter after removeing 2 screws which held it in. Shut off power and water to unit. Unplugged pump wires,removed pump. New pump came with new o-ring seals which I placed on new unit and put Vegitable oil on them for lubrication. Reinstalled unit along with wires. Reinstalled under counter, turned on water/power WORKS GREAT!