Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
snapped element
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done! recieved my replacement part the next day after ordering
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.
With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Wife said stove was on fire - Oven element shorted.
Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was fixing the oven element my wife replaced the oven light.
My oven sparked, then wasn't working, so I turned to the internet.
I received the new element on the third day, followed simple directions, and voila! I'm baking again. First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
The part came quick and packed very well. I moved the stove out and un pluged it. opened oven door and took a philips screwdriver and took the screws out at the back of element..Slid it out with the two wires attached and unpluged the conectors. pluged the conectors on to the new element and slid it back in. Had a chocolate cake in 35 minuts. Thanks, John in Texas
****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into the holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
