Main problem was the bearing, replaced the belt and felt seal as well The video instruction was very helpful Was easy with basic mechanical aptitude Dryer running great now All parts from Partselect.com Have ordered from them before and would order from them again
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!
followed the instruction on you tube, the part was exact, there was nothing to guess, basically you take the whole front off of the dryer, that in itself is easy (follow instructions), once you get to the element, just plug and play. the worst part was a set screw in the back that did take some patience, but finally did get it in. I am not a mechanic in the least, trust me, if I can do it then anyone can. you will need regular Philips screw driver and one short one, really short, mine is about 2 inches in length, also I used manual one, allot of plastic, so I would not recommend electric drill or electric driver. also a good pair of plyers, but small not large.
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
Tight quarters but went well, fairly easy except for the far back screw that secures the element to back of dryer. Would have been easier if I removed drum but I didn’t want to disassemble that much. All is good and wife is ?? . If need help with disassemble Utube is your friend.
You must disconnect appliance from the gas, water and vent to access the back. Remove the top of the dryer which then allows you to remove the rear panel by removing all screws, You may also have to remove 2 electrical connections to get this panel off. Now you have access to the air duct. To remove the air duct there are 3 screws inside the dryer and 2 screws on the lower part of the air duct. One of the lower screws is facing toward the inside of the dryer and you will need a 12"+ screwdriver to be able to remove. Once you do all that install the new part and repeat steps in reverse.
Heating element went out so I ordered this replacement and installed it myself
Getting to the element and putting the machine back together, in my case, was the most difficult part. There are tons of youtube videos that can guide you through the removal and replacement better than I can. I recomend watching those videos and taking pictures of the old element prior to removing it. Also, I would put all the screws in separate ziplock bags with labels on them because every screw for my model was unique. I would also tape and label the electrical wires too.
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
Once we got the dryer out of the cramped where we could work on it, the project went a little quicker. I'd recommend using paper plates/bowls, that you label, to hold all the screws for each piece you remove off the back. It doesn't seem like it will be a lot, but we had at least 20-30 screws in 4-5 different sizes. Unlike someone else's install, we had to completely pull the white back panel off, as well as the main back cover, due to one screw holding the air duct from the inside of the dryer compartment (meaning we couldn't reach everything from the back). Getting this screw out was a challenge and seemed like a huge design flaw, but if you can't get to that screw, the old air duct isn't coming out. There are 2 other screws holding the air duct but they're easy to reach once the back panel is off. Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.