F45QR20CW0 Frigidaire Refrigerator - Instructions

I talked to a human who spoke english and was pleasant. She managed to work with me in a timely fashion to order the desired piece of Kenmore refrigeration equipment in less time than what iiwas trying to do myself on the internet. Her knowledge that was very valuable made this experience exceptional and memorable. However, the price to replace a crisper drawer is ridiculous.

The front piece had to be removed by slipping it off the broken drawer and then slipped back onto the front of the new crisper drawer. The bottom did not exactly go where it was designed to go so there remains a gap. I could use tools or forcably try and pry it into place so it is flush and pretty but the thought of breaking it sends my wallet into seizures.

Very simple. I removed 2 screw each holding the old drawer support glide and I replaced it with the new support( 3 minutes to replace using old screws )
To replace the drawer I removed the front part of the drawer(just pop out) and I attached to the new drawer(no tools needed).
Now It looks I have a new refrigerator.

I removed the drawer fronts from the old drawers and slid them onto the new drawers. My fridge is like new again and the repair was a lot less expensive than buying a new one. My drawers arrived the day after I ordered them!!

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

Put the new shelf into position-Voila!

1. Turned off the cooling cycle and unplugged the refrigerator.
2. Removed all of the shelving and bottom basket.
3. Removed rear covering in the freezer section.
4. If frosted over, manually defrost coils with hairdryer.
5. Located original thermostat and after marking the wire locations cut the wires and removed the Thermostat.
6. Connected matching wires using a lighter to melt the wires together. Wrapped repaired wires with electricians tape.
7. Unable to install the thermostat in the recommended location (freezer is a tight fit) the new part was installed at the original location.
8. Replaced the rear cover and shelves.
9. Plugged in the refrigerator and set the cycle back to cooling.
10. Monitored freezer coils couple of days/weeks depending on how fast they freeze over (slots at bottom of cover) to validate if problem solved.

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net

We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yourself!

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Just took it out of the box, wash it and put it on the inside door.

For the shelf you have to save the front and back gaurds to put on the new shelf when it arrives. You have to slide the shelf in through the slots and then add the back gaurd. The front guard just pops on after that. The drawer front of the old drawer just slides off and then back on the new drawer, The drawer just slides in after that. No tools needed. Super easy ... super beautiful. Love it!

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.

Installed salvaged pan cover edge guards from broken pan cover. I installed new pan cover in grid.