F1320E - Instructions

Replaced diode works great. your website said 92% diode was problem and it worked. Order fuse in case old was blown did not have to use it.

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

remove outer cover of microwave, (special recessed star bit required) change bulb, unplug and remove 1 phillips screw.

I could just set the new whirly gig in the bottom hole of the micro and it worked. The new part was delivered in 24 hours of my order and hence fixed in 24 hours. Thanks so much Part Select

I disconnected the power. Took off the front panel that was held together by two screws. Reviewed the schematic that was inside. Located the switches, saw which lead was burnt. Unscrewed the two screws that held the switch in place, cleaned the connector, and put the switch in and connectors back. Powered the device, tested for cooking/heating functionality. It worked, Closed the front panel

Removed case,
Discharged HV capacitor and removed cooling fan.
Unscrewed ground end of HV diode and unplugged from HV capacitor.
Installed new diode by reversing the order. In my case, the problem was the magnetron was bad, so I replaced it as well.

Took out the old, put in the new.

I took the turntable roller guide, dropped it into the hole, put the plate back on the turntable roller guide; and voila!!! It worked!

Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.

well I unplugged the microwave one day prior to working on it. shock precaution smart way to do this job. very easy pullout the screws behind the unit pull off the outer casing. minor screws inside the unit you have to remove a couple things out of the way. unplug the magnetron and remove first gives you more room to work on the side panel to replace the micro switches. I only replaced one the bottom micro switch. only one bad, but since I was in there I clean the bulb and changed the magnetron any ways. I read other reviews and made my choice to do so. it works perfectly now. Thanks PartSelect for having parts.

Initially we started looking to buy a replacement microwave to replace our 13+ year old built-in microwave. It was a real pain finding a replacement to fit the exact dimensions. So I thought I'd try to find an old KitchenAid microwave. However, I was pleasantly surprised when this site came up on my search. Their website allows me to input the problems and then it showed two possible parts that needed to be replaced. I emailed tech support and asked them which part I needed. They responded very quickly and said I needed to replace the magnetron. I watched a couple YouTube videos and then pulled my microwave apart. It was incredibly easy to pull the outer cover off. The magnetron had 5 screws that needed to be removed and one electrical plug. Took me maybe 10 min to complete the entire repair. It was one of the easiest repairs I've done and so thankful for this site They saved me a ton of money from not buying a new microwave and we now have our microwave working again. In hindsight, I wouldn't hesitate. I'd order the Part now and get it fixed.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

Took microwave out of builtin cabinet with 4 screws.
Put microwave on center island and removed cover.
Tested interlock switch with volt meter and it appeared ok so I put my kit back in box and sent back.
Took out magnetron unit and replace with new part.
Put cover back on and test.
All is working and installed back in cabinet. Two weeks later all still working great.

There were two hard parts for me to work through.

The first was breaking off the two screws that need a special head screwdriver to remove. None of my special special head screwdrivers worked (I have a few), so I used a hammer to force them off.

The second hardest part for me was finding the correct replacement bulb on-line. My Amana Microwave is a combo Microwave/Convection type, and it's a strange little bulb - almost tube like.

Once I did find the right bulb on this PartSelect.com website it was a breeze. The part was delivered in just a couple of days (even during this Covid-19 pandemic). Once I had the replacement bulb in hand it barely took 5 minutes to install.

Thanks PartSelect!!