ESH22XGPDWW General Electric Refrigerator - Instructions

Unplugged power cord, removed back panel, disconnected wires, removed existing control board, installed new control board, reconnected wires, replaced back panel, plugged in power cord. The video instructions made it really easy. Saved at least $100.00 doing it myself. Awesome!

Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.

I repaired IAW the PartSelect video. Very easy. One thing that should be mentioned in the troubleshooting process, is to check the retention spring on the flapper. That spring could come off and also cause the flapper not to close.

I did exactly what the instructions on the e-mail stated and saved myself about 350.00! Thanks so much for the incredible service instructions and ease of getting the part needed.

We watched the video on how to install the part. When the part arrived we were all set. The video was so informative that we knew exactly where to go to install and what tools to use. This was great and we have recommended this company to anyone who needs to do repair on their appliances without having to pay for a service call, parts and labor. It cost us approximately $42.00 which other wise would have been easily $200.00 for the GE repair person or another appliance repair person

Turned power off at breaker. Took off front panel on the door. Unscrewed the panel where the electrical parts were plugged in. Then you could unscrew the old solenoid assembly and install the new one. Cleaned around the Ice shute since some mold was there. Put all back together. We watched the video from you tube about 5 times!!

Followed the Parts Select video step-by-step. It was exactly as the video described and took about 5 minutes (though I already had the cover off). Almost a week later and the refrigerator is running fine.

I replace defroste thermostat :i defrost al the ice

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

The instruction sheet (2-pages) supplied with the main control board were simple to follow. I removed the cover in back, carefully unplugged all the cable connectors, unscrewed the green ground wire, and lightly pinched the four white mounting pins with my fingers to release the old board. I then snapped the new board onto the four white pins, plugged all the cables back in, attached the ground wire under the closest available screw, and closed it up. I did not need to cut any wires. Plugged the refrigerator in and it's been running fine all day. The whole job took less than 10 minutes.

Unplug the refrigerator and remove frozen food, shelving, light and back panel inside the freezer section to expose the cooling coils. The coils were completely iced over. Using a wet dry vacuum to discharge the air toward the coils quickly melted the ice. The trouble shooting section on your website described my problem and I bought both items which were the most common problem. Using the video(s) e-mailed to me when purchasing the parts provided great information regarding details for the repair. After replacing both parts the refrigerator is working great having spent just under $25.00.

Removed the trim around the entire opening. Be very careful. The trim is held in place with 4 pressure "prongs" on each side and 2 at the top which can easily break (I broke 4 of the 10 not knowing this). Two are 1/2" from the top and bottom, the other two are at about 1/3 from the top and bottom. There is a slot on either side under the bottom of the trim. Insert a screw driver in one and carefully pry the side up enough to slide a knife or putty knife under the trim and press the first "prong" to release the trim. Release the remaining three, then the 2 at the top. The trim should come off then, but if not you may have to release the 4 on the other side.

Next remove the control module which is also held in place by 2 prongs on the bottom. Insert a long screw driver behind the module to release the prongs and release the module. Alternatively, press down on the top side very carefully to avoid breaking the plastic until it releases. Remove the electrical sockets from the circuit board to get the board out of the way. I could not get the larger one to release so I taped a folded paper towel over the circuit board to avoid shocking or damaging the board as it hung there while I did the rest of the work.

Remove the 4 screws holding the ice funnel unit. Remove the unit and release the tension on the spring ASAP because the plastic “plate” above it that helps hold it in place is thin and fragile. (The corner of the plastic plate cracked and bent upward on mine so that I feared it was going to break off altogether when I put the tension back on the spring. So, I laid a 4" metal strap over it and secured it with 5 large paper clips to stabilize it. So far it is working.)

Remove the old funnel and install the new one.

Reassemble everything.