EI28BS36IS4 Electrolux Refrigerator - Instructions

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

Having the same problem

remove the old one and replace with the new one and yes it was that easy. All of the lines and wiring connectors were color coded

Just follow the instruction that come with the valve. Easy.

We followed the online instructions and tah-dah it was working...

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

removal of the old valve to identify the problem took the most time. Once the new valve came it it was easy. NOTE: the old one had threaded connectors, and the new one is press/fit so the ends of the tubing need to be cut. The color coding and size matching are great.

Simple, I had a repair man come over and diagnose the problem. After confirming, I ordered the part and replaced it. Need to make sure you get the ice build up out of the fitting tnat goes from the back of the fridge connection at the top and the filler tube inside the unit, mine was iced over. Repair man wanted to charge me $250.00... with his service call and buying the part, it cost $120

Very easy repair, instruction were clear and easy to follow

I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

Watched the video and read some comments and from that it was easy

This is an easy repair. Unplug appliance. Remove the old water valve by unscrewing it from the frame of the refrigerator. Disconnect the cables and all the water hoses. The hose fittings are a different type: clip off the old connectors from the hose ends and push the hoses straight into the new connectors till they fit solidly. Reconnect the cables and screw the valve back onto the frame of the refrigerator.
Unfortunately, my leak was from a hose, not the valve, so this didn't actually fix it.

took existing water valve loose, removed plastic water lines and reinstalled on new valve and installed new valve into refrigerator