EF36IWFSS Refrigerator - Instructions

The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..

Removed two screws on outer face plate and set aside the face plate after disconnecting from power supply. Remove dispenser paddle which had broken and replaced with new part. Reattached power connections and reattached the face plate. Relatively easy process.

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!

I unpacked the glass and slipped it into the shelf. Done.
What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Repair was simple and just as described by several others on this site! From finding the part, ordering, quick shipping and instructions, PartsSelect made this job a breeze to complete.

Replaced the left side endcap for the drawer. Three screws and it popped out. Easy process once I actually looked at it. Drawer cover now works as designed. Replaced inline water filter. Not problem there.

Replaced the control board. Called another web site and for $15 got the twelve step code to set the new control board.

Still no cooling. Same issue as before.

Sears coming again tomorrow to try again.

Extremely simple to replace the entire cover. Just had to press on the sides to remove the cover from the hinge pins, then reinstall.

The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!

after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select

Thanks to others who shared their story, I was prepared to "muscle" the front cover off the old crisper and snap it into place on the new crisper -- warning if you are good with puzzles and mechanics, this repair is a "snap"; Pantry Lid is very easy, push pin on left side, slide old lid out and push new lid in.

Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".

To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.

The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.

Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.

The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.

Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.

Once the motor module is seated, replace the 3 screws and push the white cover back on.

Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.

Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.

The icemaker should start making ice within 2 hours.

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

Two phillips head screws out to remove drawer slide. Three screws to remove right side drawer support. New support placed, new lid snapped into place. The right side has an adjustment lever. Re-routing that took the longest. The arm had to be removed and twisted to get the adjustment knob off and on.