E23CS78HPS0 Electrolux Refrigerator - Instructions

The molded plastic bracket holder on one of my shelves was busted. It was obvious I just needed that particular part, and didn't need a full 'service technician' rigamarole. It's great to have been able to find the part online. If arrived fast and took less than 5 minutes to fix!

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

The defrost thermostat kit is located in the freezer side of the refrigertor. I turned off the electrical breaker for the refrigerator. I began the project by removing all the frozen food on the lower half of the freezer. I removed the racks and 3 rails on both sides using a cordless drill with a 1/4" socket and located panel. The panel had 4 1/4" screws holding it to the back of the freezer. I removed all screws and the panel came out easy. I located the defrost thermostat and with some wire cutters, I cut the wires. I connected the the new defrost thermostat with wire connectors and reattached it to the copper tube I removed it from. I put the panel back on along with the side rails and racks.. This project was very easy.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

I watched the do it yourself video which helped tremendously. My husband was busy so I was able to do it myself.

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

Fortunately, this was not hte first time to do a repair on the through the door dispensers. I turned the unit off and removed the door tray (slides out) to expose the screws for trim removal. When that is removed, you remove the circuitry and then remove the actuator and spring. It was difficult to get the new actuator in place. the "stop" which holds it in pace is not forgiviing! And that is being mild. (I remember a few explitive delitives I thought wer gone foreever! I reconnected the circuit to the panel, replaced the panel, and the tricky part was to reinsert the water hose into the dispenser hole. Good luck. When that was in, the entire unit was reeturned with the four screws. The front trim panel was replaced with four screws, and the slide in drip tray was slid in. Job done, and the power was restored. Thank goodness I had some long hemostates to control the reinsertion of the water tube!

took old valve off one peice of it was broke off from freeze replaced it with new valve all but one conection was quick connect electric connections were color coded quick fix works fine thanks Gary

The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.

I followed the video instructions from your site and it couldn't have been easier.

After receiving the parts, I clamped on the connector ends, and put on the shrink tubes. Unplug frig, took out the shelves (4) screws, unscrewed back panel (4) screws. Took old thermostat off tube, clipped (2)wires on old thermostat, splice wires, clamped connector on old wires, moved up shrink tubes, and used a heat gun to shrink the wires. Put new thermostat on the tube the old one came off of, put panel, and the shelves back. Pugged frig in. Works great!

electrical unplugged. water turned off and disconnected. cardborad backing off (4 screws). removed part (2 screws). unplugged electrical connections. removed each line one at a time and inserted into new part, connected electrical connections. placed new part with all connections back onto refrigerator, (2 screws), backing back on, water line connected, and electrical connected. no leaks with new part. simple uninstall and install for do-it-yourselfer. instructions need to be printed in larger font for easier reading.

Followed instructions on removal of door, replaced bottom plastic bearings. Lubed with some grease. Viola! (Actually was just the hinge bearing that was broken, so could have saved 6.00 but I figured why risk it and replaced them both.)

Took door of and replaced bearing Two screws . HARDEST PART WAS TAKING FOOD OUT OF DOOR.