DW9000AWW1 Frigidaire - Instructions

I called an appliance store and they said to bring in the model number and a deposit and they would order it for us. Then, I decided to go to the Internet. I Googled Gibson Dishwahers and your page came up. I entered the requested information and ordered the gasket. In LESS THAN 24 HOURS it was delivered and in les than fifteen minutes, our son installed it. No more leaks! Thank you for the excellent service.

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

This site had good pics and descriptions of the gasket I needed, as well as a LOT of users instructions concerning installation. Ordered, came quickly. It was a little hard to push in the groove. (Maybe a little silicone lube on the gasket would help??) I also filled in the gap at the bottom with a small section of the old gasket, as suggested by (other) installers. Why not? Anyways, it took both hands to close the door the first 3-4 washes. Easy to open/close now. AND... no more leaks! Great price, too!

Just snapped the wheels on and attached the bracket to the existing part.

The gasket was easy to remove and easy to replace. Our story is interesting because upon calling SEARS to find the replacement part we were told they no longer make it because the dishwasher is too old (approx. 15 years). It works wonderfully so I was annoyed to think we'd have to buy a new one just because of a bad gasket. My husband has a knack for finding things online and eventually discovered your site as well as the original drawing of the machine to find the part number and lo a behold, it fits perfectly. No more leaks! Sweet

At first remove the lower rack to give more room for you to lean over the inside of the dishwasher then remove the old gasket tub 90 inches long make sure that you know which side goes where, so that it will be easy to put the new one. Then press the gasket firmly on the side.Now you can start your dishwasher with no leak and saves you a lot of money for buying a new one.

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

The repair was simple. When the part comes, you may need a hairdryer to heat up the plastic a bit to get any kinks that may have happened during packaging or shipping, very easy 5 minutes. Removed the old gasket by hand, very easy, 1 minute. You will need to clean out the track that the gasket sits in. Mine had years of black gunk inside of it. You will need qtips or a small screwdriver with some tissues or papertowels, easy but took 15 minutes to clean out properly. Installed new gasket in the track, start at the top middle, there is a notch on the gasket so you know where the middle is. Installed by hand, just push bottom edge into the clean track, easy 5 minutes. Ran the dishwasher with no leaks. Very pleased with the result and how easy the gasket was to remove and install.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!