DP8500XXN3 Whirlpool Dishwasher - Instructions

Very easy repair. I gently removed the rubber seal at the top of the tub. here I found the 2 holes to screw the new plate into place. Put the seal back over the hole and job done. Thanks for all the help from the very supportive staff. Yes, a woman did this repair. Dishwasher working like brand new!

Mine is a Ultra Wash 111
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Purchased and installed new faucet attachment. It arrived quickly and very easy to attach. Thank you !

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

I bought the kit because it had other parts that I thought I needed.

It was a piece of cake, just slapped together and slid it into place!

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.

Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.

Hint - Order at least 2 springs! They are not expensive.

I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.

I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.

So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.

Take care

Easy fix. It’s a screw on by hand piece.

after that every thing went very well