Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dishwasher was noisey holding dirty water.
removed the upper and lower baskets, removed the lower wash arm by rotating the center bearing assembly (its the flat piece in the very center of the lower wash arm) by the way it has a reverse thread...not righty tighty and lefty loosey... it is reverse the normal rotation.. i unlocked the upper arm assembly from it's clip on to mount as well as the clip on to mount on the back wall, looking at the very center pump cover strainer, you will see that the assembly that goes from the pump area to the very top of the machine needs to be rotated clock wise where it locks into the pump strainer assembly. now remove the four star type screws from the face of the strainer, now you can lift out the entire bottom of the machine you will see the half round cover in the bottom of the well, remove one smaller size star screw. simply remove the chopper assembly and install the new assembly as indicated in the instructions provided, be sure to use the trick with the open end wrench as per instruction sheet, makes it easy. now follow the bread crumbs you left on the yellow brick road to reassemble.
After several weeks of decreasingly clean dishes on the top rack of our dishwasher, I did some digging & found that my chopper assembly was broken (the washer had come off & the parts were loose). I ordered a new chopper assembly here. Once I received it, the entire repair took less than 30 minutes. I removed the old chopper assembly, used a shop vac to remove the excess water & food particles, then reinstalled the new chopper assembly using the instructional video provided. The dishwasher is back up & running like brand new. The top rack is getting cleaned thoroughly once again. PartSelect made the process extremely easy & affordable!
Kill power to unit. Turn off water supply. Remove front access panel. Remove screw holding valve housing. Remove valve. Disconnect water lines. Replace valve in housing. Reconnect water lines with addition of thread tape. Reinstall valve and housing.
Element was no longer working. Dishes were not drying.
Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.
top rack quick washing water was not spinning throught top
checked all the plactic tubes for clogs used water hose and they worked ok checked into top of pump found chopper assembly had come apart replaced washes like a new one
Top rack of dishwasher kept pulling all the way out
Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer. Thank you. Sue M Masdsachusetts
Washer kept clogging the screen and dishes weren't coming clean.
I didn't finish the repair because there was a wrong seal in the kit. The factory impeller kit 8193951A from Whirpool comes with a totally different seal that I took out of the washer and the schematics from their own website and the manual shows the exact same seal that I removed, but is not even close to the one I received. I am stuck with a good dishwasher that I have to junk because of a $2 seal that whirlpool won't help me with. So much for customer service.
Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!
Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS
It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.