DLW - Instructions

For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my

First I took the front shield off, then I took the motor off.

Disassembly
- Took the back bottom plate off.
- Removed hoses.
- Removed pump with pulley (3 nut screws)
- Removed belt

Installed new parts
- Installed pump with pulley (3 screws)
- Installed belt by placing on 2 small pulleys, then turning onto the large pulley (used a screwdriver to help align over pulley for leverage).
- Replaced hoses
- Replaced back plate.

just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.

I suggest if you are replacing the pump, order the belt at the same time, you must remove the pump to replace the belt.

I decided to replace the entire agitator. The Dispenser, Agitator, and the screw had already come off when it broke. All I had to do was pull/slide the base off the motor. Then I slid the new base in place, slid the agitator on top of the base. I then screwed in the retention screw (which was probably the hardest part due to the small access). After that I snapped on the Softener Dispenser and I was done.

Not only very loud at spin cycle, but started to leak water as well. Pulled lower front panel off and ran a load of clothes while laying on the floor with flashlight watching. Sure enough, water spraying out from outer tub bearing area.
Remove top front panel, sides and top, disconnect hoses and unplug wires at top of control panel, there is a plug in there. Now you should just have base unit and tub exposed so you have plenty of room to work. Next joy is to remove agitator. This is where my fun began. After removing fabric softner dispenser from top of agitator, I could not see bolt holding it on. There was a long plastic rod sticking up which looked like part of the agitator itself, so went online to a repairmans site and they said simply pull that rod out and bolt will be under it. Paid 24 bucks to them and still could not remove rod, ended up going thru slots in side of agitator with a small chisel and cutting it off, then took a 3/4" hole saw and drilled hole in top of agitator, its only about 1/8" thick and what do you know, THERE is the bolt!!!!!!! Removed bolt and out comes agitator. Next, remove cap from outer tub, take 4 bolts out of inner tub, remove inner tub. Next, remove plastic nut from shaft, I tried this with channelocks and could not budge it, ended up splitting nut with chisel and slightly damaged threads on shaft which I cleaned up easily with 60 degree thread file. Be very careful if you use this method. You can use channelocks to reinstall, just clamp on the unfinned part of nut.Take out the lint filter and throw in garbage, do not reinstall!!!!!! That filter is part of the reason tub bearing goes out!! Next, remove aluminum hub from shaft, mine was already loose so was easy. If yours is tight, screw in one of the old inner tub bolts almost all the way in and use hammer and punch to loosen. You can do the same for new one. Next, remove 6 bolts from outer tub and pull outer tub off shaft.Flip outer tub upside down and gently pry bearing out, mine came out easy as was spinning inside tub bearing fit. After cleaning everything I used Scotchseal 800 industrial sealant because bearing fit was loose. I made a clamp out of 1x2 wood and a long 1/4" bolt to hold bearing in tub to prevent it from pushing out, sometimes the sealant will cause this to happen, then I let it setup for 24 hours. Put it all back together, no leaks and SUPER quiet. Be sure and check your bottom bearing too while you have it all torn down, mine was fine. Do not forget to change O ring on spline shaft before reinstalling agitator. As far as the hole I drilled in agitator, just tapped it 1/2" pipe and screwed in a plastic pipe plug. You will need an extension and a 5/8" 12 point socket to do this.

Following on-line instructions for the dis-assembly. Replaced bearing and seals for outer drum bearing and cleaned and lubed assembly.

Removed front panel.
Released 2 springs on belt tensioner.
Rolled drive belt off pulleys.
Unscrewed 4 bolts holding washer motor assembly.
Tilted motor to get at pump screws.
Removed 3 pump screws and pump slid right off shaft.
Aligned new pump and reinstalled screws.
Set motor assembly loosely in place.
Rolled drive belt onto pulleys.
Re-attached tension springs.
Installed motor assembly bolts.
Re-installed front panel.

** I should have replaced drive belt at same time, but it is working with no leaks.

Pulled motor, as the belt will not come off unless you take to water pump off off the motor. Installed new idler wheel, washers, clips and belt. Reinstalled motor.
Works good and hopefully lasts a long time!

Place black rubber adapter on the end of the drain hose and stick in the stand pipe drain. That's all.

i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy