DLSR483GG3WW General Electric Dryer - Instructions

My dryer was making a loud stretching sound which I thought, because of previous experience, could be fixed by replacing the bearing slides. The problem turned out to be that the blower wheel that is attached to the motor was loose. I pushed the blower wheel all the way in so that about 1/4" of the motor shaft sticks out. I then tightened the bolt with a socket wrench. Problem solved.

My dryer was making a grinding noise so I tore it apart using a screw driver, a torks bit and a pair of pliers. It took about 15min to get it appart. I found the idler pully was worn out and broke in 2 pieces. I ordered the new part along with a new belt, since I had it appart, and they arrived the next day. It took about a half hour to put the new parts in and put the dryer back together. Works great now. While I had it apart I cleaned the elements and greased the bearing.

Gave Parts to wife and she fixed it (she Broke it)

(1)I watched the videos here and read other comments about the problem... (2)Decided since I have the dryer apart, I might as well replace other parts that probably should be replaced too. (3)Make sure you order two of each of the Drum Bearing Slide-White and BEARING SLIDE (gray color), They are not sold as pairs! (4)following the Front Drum Slide video, the job was very easy.

I will not go into detail how I installed the part because I'm sure many has posted it already. At first I thought my washer was shot and have to buy a replacement. I was about to do that when I decided to search the internet for possible causes and repair. You see, I don't know squat about washers and when I found Part Select's website not only did they guide me through the diagnosis they also have a video detailing how to replace the broken part. Saved a lot of money. Spent $45 compared to $500 for a new washer. Thanks Parts Select. You sure put the handy in man.

The actual repair was simple, however, I initially ordered the wrong part. The exchange to the correct part was very easy and delivery was quite quick. I will use Part Select in the future when ordering a part for a simple repair.

Turned off all power. . . Took top back off. . . Retored starter back in position. . . Attached knob. . . Replaced back, turned on power. . . And thanks to utbe instructions

Take off the broken knob and snap on the new one. Take's less than 2 minutes. You make need a pair of needle nose pliers.

Had to replace the front air duct assembly, Front Drum Bearing, both Drum Bearing slides-white and both Bearing Slides. Googled how to repair loud noise. Followed video and found trouble in 5 minutes Ordered parts from PartSelect.com as required on video to fix. When parts arrived went back to PartSelect video followed instruction how to repair and fixed with new parts in less than 30 minutes.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

Very easy to install, snaps right in.

The part was shipped quickly and I received it within the week. I was afraid that because it is an older dryer the new handle would not be compatible, but it was! It installed easily, it only took a few seconds to clip it in and now it's as good as new!

I watched a video on PartSelect.com, opened up the dryer (that's the first time I had opened a dryer), found that the bearing was worn down, ordered the replacement parts for under $40, and fixed the dryer in just a few minutes. The whole process was much easier than I expected. I should have done it weeks ago.

At first I thought it was the belt but when I took off top portion of dryer I saw belt was fine. I got to this site and found source of noise was drum bearings from postings. I ordered the parts and much to my suprise had it working with 15 minutes. Web site was very helpful.

Pulled clip off and installed new knob