Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.
Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.
There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.
I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.
Followed video instructions step by step. I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles 1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together. Works like a champ.
1. Turned off circuit breaker 2. Pulled out dishwasher 3. Disconnected switch and popped out switch 3. Popped in new switch and connected 4. Pushed dishwasher back into place 5. Turned on circuit breaker 6. Turned on dishwasher and it worked
Dishwasher would not fill with water and would shut off
I found it online! There were step by step instructions that were easy to understand. I have never had to do anything like this in my life, only recently had to start doing everything around the house myself due to husband's illness. The repairman came out, charged me $100 to determine what the dishwasher needed & left me with the part number. He was going to charge me $389 to install the part and they were over charging for the part. The repairman suggested I just get a new dishwasher. I ordered the part from the website at 1/2 the price that the other place charges and found it on line. With the step by step instructions and the online page, I successfully installed it MYSELF. Saved me a ton of $$. I LOVE the website Thank You!!!!
-Disabled power. -1/4” nut driver to take off kickplate. -Unplug wires harness to door -Dismount dishwasher from cabinets and pull out 4-6 inches -uncouple spring pulley from door hinges. -Open dishwasher door about 4 inches and pull out and up to remove -Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door) -remove vent cap and push up on interior plastic door casing to separate outer and inner door. -Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal). -Reassemble the inner/outer doors and reattach to dishwasher in reverse order. Be sure to plug the doors electric harness and kickplate. -Plug the dishwasher back in and run it through a test.
I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.
I would read this project very easy for somebody with technical skills and easy with no prior skills
