DCVH515GF1GG Dryer - Instructions

I first ordered the coils from a different web site and they sent the wrong ones. The job would have been much eaiser if i had just returned and ordered from here. Instead i cut wires and tried the others but since they were worng, it did not work. I didn't label the wires so it was a puzzle to put it back together. Once i had the wires connected properly it was a simple fix. You just open the top and take the front pannel off, remove the drum and it is right there at the bottom. Two screws take the cover off of the coils and they slide off the gas valve. Slide the new ones on and replace the cover. Put the front pannel back on, close the top and its good to go. I first tried the highlimit thermostat, and termostat with no luck. The flame would light when it was cold, but once warmed up, the flame would ignite and immediatly go out. The coils did the trick.

I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.

Someone I'm related to by marriage accidentally dried a plastic-coated tablecloth on high heat, and our heat deflector was hosed. I was very happy to find this part here for such a reasonable price; Sears wanted about $65 for it. Installation required a Torx bit, and removing the old one was easy, but the dryer's design made it difficult to reinstall the heat deflector while keeping the dryer running concentrically. I ended up cutting the heads off three screws, threading those into the plate behind the drum, sliding the new heat deflector on over those, and then one by one replacing them with the original Torx head screws. Once I figured it out it didn't take long but it took me a while to figure it out. That's probably more a reflection on me than the dryer!

First I had to remove the top by taking out the two screws inside the door. Then I removed the front by taking out the two screws holding it from the inside. I needed to remove the drum and to the the belt off, I removed the left side. It has several screws down the back, two on the bottom and two in the front. I removed the belt and drum. I took out the old sleeve bearing. Part of it was broken off into the hole it goes into. I then had to remove the plate that holds the heating element. Once that was done, I put the new bearing on and replaced the drum slides on the from section. Then I reversed the process to reassemble. Not too bad.

Everything is cleaned as it is removed.

Remove the two screws holding the top down.
Disconnect two wires from door switch.
Remove the two hex screws holding the front on.
Remove the 4 screws holding the access panel on the back and disengage idler pulley to loosen the belt.
Remove the drum.
Label the wires then remove the heating element.
Check orientation of ground strap before disassembling rear bearing.
Remove four screws holding rear bearing to back of heating element.
Install rear bearing and ground strap on to heating element.
Reinstall heating element.
Reconnect wires.

Most Important : Get help putting parts back on drum! I didn't and that's why it took over 2 hours.
I will describe how I did it.

Unscrew bearing from inside of drum.
Wrap screwdriver with tape to a little larger than the screw hole.
Use small screwdriver to line up the drum, shim and deflector.
Don't forget the brass shim. It wasn't on the parts diagram.
Start two screws don't tighten them yet.
Remove Screwdriver and start third screw. Tighten all three down.
Put belt on drum.
Install drum and belt.
Reverse disassembly.
When putting the front on make sure drum rests in the felt.

I rated this a bit difficult because I did it myself. With help this is a fairly easy repair.

Replaced idler pulley and belt very simple

I googled the problem and found a forum where people were having the same problem. Luckily I found a post that told me the exact parts I needed. I then found a video on youtube, followed every step and completed the repairs in about 45 minutes. I'm a housewife and found this fairly easy. The dryer now works like a charm!

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

i took the front load dryer apart found the parts that were bad ordered the parts which were a snap at partsselect at first i thought it would be tuff to put back together but the site has good pictures i put the dryer back together but had a tuff time with the belt after i watched a video it went right together i found that taking pictures with my cell phone while taking things apart helped a lot when putting it back together all in all im proud of myself i didnt think i could do it but i did and the dryer works great i will be using the site again i used it a few months ago for my washer it it worked great too!!

Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

I bought a natural gas orfice for a dryer that needed to be change from Lp gas. I was able to
change the parts,it was very helpful that there was a drawing in the package showing the
location of the parts that need to be changed. This was a used dryer I purchased and
I did not have an owners manual to refer to.
Everything went very well, Thank you.

Marcia

I followed the directions that were listed on this site by other Do It Yourself individuals...by the way I'm a lady and more mechanically inclined than my husband, but he was a great help in lifting the drum up and out. (I unplugged the dryer before starting repairs)
1. I removed the two screws located at the top of the dryer inside the door.
2. Top of dryer cabinet lifted up after screws were removed.
3. Located and removed front panel retension screws and removed front panel and set aside
4. slipped belt off motor by reducing tension on idler pully
5. Removed screws inside drum that secured drum to bearing assembly
6. Husband and I lifted drum up and out of cabinet (this went very smoothly and took less than 15 minutes time.
7. Followed supplied bearing drum instructions and removed old bearing and installed new assembly.
8. Thoroughly cleaned out internal cabinet, blower, and motor areas
9. Reset the idler pully into proper position.
10. Tipped dryer on 'back' to reseat the drum With A NEW DRYER BELT (taped temporarily around the drum) into the bearing shaft (I may not be using the proper terms)
11. tipped dryer upright and while Hubby balanced the drum, the front panel was resecured to the rest of the cabinet.
12. Removed temporarily applied tape that held the drum belt in the general position, then using the rear access panel, I slipped the belt over the motor into the proper posisiton.
13. Top cabinet was reapplied and screwed into
place.
14 Plugged in and tested the dryer...NO SQUEAKS and it works beautifully and quietly!!

The job is not terribly difficult, but I am only 5 feet tall and the drum is bulky to work with and balance. Reaching into the cabinet to slip the belt onto the motor stretched my arm to the limit.
I found the cabinet reassembly and realignment of the screw holes quite annoying. But the total job proved satisfying upon completion.

I removed the door and "flipped" it to open right to left. Rather than remove the existing door latch I added the purchased latch on the right side to enable opening the door right to left or left to right.

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !